該頁無縮略圖
功能說明
1.單作用彈簧回縮。
2.螺母鎖定使負載更安全。
3.特殊復合材料涂層使耐腐蝕能力更強，使操作摩擦力更小。
FUNCTION
1.Single-actingring.
2.Safely locknut forsafeoperation.
3.Special synthetic coating for increased corrosion resistance and decreased friction. CLL液壓缸，在立交橋定位后， 機械鎖定。
CLLcylinder,mechanically locked,after positioning the curved bridge.
在這一立交橋中，CLL油缸用來支撐混凝土梁，調平支座并將4000噸 的滑動軸承置于橋墩與支座中間。 Inthecloverleaf junctionconstruction,CLLcylindersare beingused tosupport the concrete beam,level the bridge bearingsandplace the 4000 tons sliding bearing between the piers and bridge bearings.
| 型号 Model | 吨位 Tonnage (T) | 行程 Stroke (mm) | 配置泵浦 Matching pump | 本体高度 Closed height (mm) | 重量 G.W. (Kg) |
| CLL-1050 | 10 | 50 | CP-700 | 160 | 5 |
| CLL-10100 | 10 | 100 | CP-700 | 210 | 6.5 |
| CLL-10150 | 10 | 150 | CP-700 | 260 | 8 |
| CLL-2050 | 20 | 50 | CP-700 | 160 | 7.5 |
| CLL-20100 | 20 | 100 | CP-700 | 210 | 9.5 |
| CLL-20150 | 20 | 150 | CP-700 | 260 | 13 |
| CLL-3050 | 30 | 50 | CP-700 | 160 | 9.7 |
| CLL-30100 | 30 | 100 | CP-700 | 210 | 12 |
| CLL-30150 | 30 | 150 | CP-700 | 260 | 17 |
| CLL-5050 | 50 | 50 | CP-700 | 160 | 15 |
| CLL-50100 | 50 | 100 | CP-700A | 210 | 20 |
| CLL-50150 | 50 | 150 | CP-700A | 260 | 25 |
| CLL-10050 | 100 | 50 | CP-700 | 187 | 31 |
| CLL-100100 | 100 | 100 | CP-700A | 237 | 39 |
| CLL-100150 | 100 | 150 | CP-700A | 287 | 47 |
| CLL-15050 | 150 | 50 | CP-700A | 209 | 54.5 |
| CLL-150100 | 150 | 100 | ZCB-700AB | 259 | 66 |
| CLL-150150 | 150 | 150 | ZCB-700AB | 309 | 79 |
T！ V#
功能說明
1.雙動式液壓回油。
2.烤漆成型，增大了抗腐蝕的能力。
3.內置的安全閥，防止意外過壓發生。
4.需配雙回路泵浦使用。
FUNCTION
1.Double-acting,hydraulic return.
2.Baked enamel finish forincreasedcorrosionresistance.
3.Built-insafelyvalve preventsaccidental over-pressurixation.
4.Be equipper with double-loop pump to use.
在立交橋中用RR油缸替代調節滾輪，提供受控的頂升與下降
Replacingadjustment rollsundera fly-overwith RR cylinders,for controlled lifting anlowering.
在重型負載定位精確控制中，RR油缸是最佳的解決方案。RRcylinderis the best solutionto precise controlled heavy loads.
| 型号 Model | 吨位 Tonnage (T) | 行程 Stroke (mm) | 配置泵浦 Matching pump | 本体高度 Closed height (mm) | 重量 G.W. (Kg) |
| RR-10250 | 10 | 250 | ZCB-700AB | 405 | 12 |
| RR-10300 | 10 | 300 | ZCB-700AB | 455 | 13 |
| RR-10250 | 20 | 250 | ZCB-700AB | 405 | 15 |
| RR-20300 | 20 | 300 | ZCB-700AB | 455 | 17 |
| RR-30200 | 30 | 200 | ZCB-700AB | 390 | 19 |
| RR-30300 | 30 | 300 | ZCB-700AB | 490 | 24 |
| RR-50200 | 50 | 200 | ZCB-700AB | 390 | 29 |
| RR-50300 | 50 | 300 | ZCB-700AB | 490 | 36 |
| RR-100200 | 100 | 200 | ZCB-700AB | 390 | 52 |
| RR-100300 | 100 | 300 | ZCB-700AB | 490 | 58 |
技術參數
爪式千斤頂BY-10爪部出力：2.5ton揚程：117mm本身高：228mm伸長總高： 3 4 5mm 主軸直徑：29mm底座尺寸：130\*125mm爪高：16mm總重：8.5kg適用于重機械校正水平用，及一般干斤頂無法使用的狹小場所。
Technical parameters
Jack BY-10 claw contribute to the Department:2.5ton
Head:117mm Itself is high:228mm
Elongationoverall height:345mm Spindle Diameter:29mm
Base size:130\*125mm ClawHigh:16mm
Total weight:8.5kg correction applied to the level of heavy machinery use,and general jackcannotbeused insmallplaces.
47 JIMU TOOLS
功能說明
1.緊湊、輕便、快速，可在3mm以下碳鋼板上開制圓孔、方孔等，可配合其它特殊開孔模使用，無間斷定向驅動，使接近工作點更容易。
2.開孔范圍廣，可在開關箱、配電箱、儀表板、鐵板穿孔、沖孔，作業便利，沖孔齊平、無毛邊。
3.含6種尺寸沖孔模具、2個螺栓、1個墊圈、開孔機本體以及塑料提箱。
4.配上方模可開多種方孔，特殊規格的圓模方模可訂制。
FUNCTION
1.Compact, light, fast. It could be used on carbon steel plate for digging round and square holes in 3mmorbelow.Itcould also beused withotherspecific dies of holedigger.Thesolidpositioningdrive leadtoapproachworkingpointeasily.
2.Wide hole digging range.It could be used onswitchboard,power transmission panel,meter plate,steel plate to dig hole or punch hole.Operate conveniently, punched holes smooth without burr.
3.lt covers six kinds of dies,two bolts,one washer,hole digger unit and plastic carrying case.
4.It couldbe used for digging square hole iffitted with square dies.Any specific size of roundand square diescould be ordered.
| 型号 Model | 出力 Output | 行程 RamStroke | 开孔能力（mm） Punching Capacity | 配置模具 Punchdies | 整机重量 G.W. | 体积 Volume | ||
| Plate Thickness Pu开ange | ||||||||
| StainlessSteelIronSteel | ||||||||
| SYK-8A | 8 | 25 | 1.6 | 3.2 | Φ16-Φ51 | 16，Φ20，Φ26.2，$32.5，Φ39，Φ51 | 10 | 48x26x13 |
| SYK-8B | 8 | 25 | 1.6 | 3.2 | Φ16-Φ60 | Φ22，Φ27，Φ34，Φ43,Φ49，Φ60 | 12 | 48x26x13 |
| SYK-15 | 15 | 25 | 2.0 | 4.0 | 16-114 | Φ63,Φ76,89,Φ101,Φ114 | 20.5 | 48x26x13 |
| SKP-8 | 10 | 25 | 1.6 | 3.2 | Φ16-Φ60 | Φ21.8,Φ27.6,34.1,42.7,47 | 13 | 48x26x13 |
| SKP-15 | 15 | 25 | 2.0 | 4.0 | Φ16-Φ114 | 21.827634142747 | 21 | 48x26x13 |
功能說明
1.緊湊、輕便、快速，可在3mm以下碳鋼板上開制圓孔、方孔等，可配合其它特殊開孔模使用，無間斷定向驅動，使接近工作點更容易。
2.開孔范圍廣，可在開關箱、配電箱、儀表板、鐵板穿孔、沖孔，作業便利，沖孔齊平、無毛邊。
3.含6種尺寸沖孔模具、2個螺栓、1個墊圈、開孔機本體以及塑料提箱。
4.配上方模可開多種方孔，特殊規格的圓模方模可訂制。
FUNCTION
1.Compact,light,fast. It could be used on carbonsteel plate for digging round and square holes in3mmorbelow.Itcouldalsobeusedwithotherspecific dies of hole digger.The solid positioning drive lead toapproach working point easily.
2.Wide hole digging range.Itcould be used on switchboard,power transmission panel,meter plate,steel plate todig hole orpunch hole.Operateconveniently, punched holessmoothwithout burr.
3.lt coverssix kindsof dies,two bolts,onewasher,hole digger unitand plastic carrying case.
4.It could be used for digging square hole iffitted with square dies.Any specific size of round and square diescouldbe ordered.
| 型号 Model | 出力 Output | 行程 RamStroke | 开孔能力（mm） PunchingCapacity | 配置模具 Punchdies | 整机重量 G.W. | 体积 Volume | ||
| Plate Thickness | Pu开孔范ange (mm) | |||||||
| 不锈钢 Stainiess SteelIronSteel | 铁板 | |||||||
| SYD-32 | 6 | 95 | 1.2 | 2.5 | Φ10-Φ32 | 模具Φ16,Φ20,Φ25,28，Φ32， 可定做模具 | 3 | 43x30x13 |
| SYD-32F | 6 | 95 | 1.2 | 2.5 | Φ10-Φ32 | 模是1，20,中25,中28,32， | 2 | 23x30x13 |
| WK-8 | 8 | 25 | 1.6 | 3.2 | Φ16-Φ60 | Φ22,Φ27,Φ34,Φ43,Φ49,Φ60 | 3.5 | 43x30x13 |
| CC-104I | 15 | 25 | 3.0 | 4.0 | Φ16-Φ60 | Φ22，Φ27，Φ34，Φ43，Φ49，Φ60 | 3.3 | 42x23x13 |
| TPA-8 | 6 | 22 | 1.6 | 3.2 | 16-Φ60 | Φ22,Φ27，Φ34，Φ43，Φ49,Φ60 | 6.5 | 43x30x13 |
| MAP-8 | 8 | 22 | 1.6 | 3.2 | Φ16-Φ60 | Φ22，Φ27，Φ34，Φ43，Φ49，Φ60 | 7.5 | 43x30x13 |
| MAP-8Z | 8 | 22 | 1.6 | 3.2 | Φ16-Φ60 | Φ22，Φ27，Φ34，Φ43，Φ49，Φ60 | 8.5 | 43x30x13 |
功能說明
1.先以電纜3/8"(9.6mm)沖孔即可讓R-1配上1/2”上下刀模，再套上棘輪式活動扳手開始操作。
2.鐵板厚度3.2mm不銹鋼2.0mm以下。
3.新產品省力型，所穿越的鐵屑為兩片。
4.不需油壓泵浦與油壓缸，可節省費用成本低。
FUNCTION
1.First drill 3 / 8 ^ { \circ } ( 9 . 6 \mathsf {mm } ) holeto fit 1 / 2 ^ { \dprime } up and down knife die on R-1.Then put on
ratchetmoveable spanner.Now begin to operate.
2.Steel plate thickness 3 . 2mm .Stainlesssteel 2 . 0 \mathsf {mm } orbelow.
3.Newproductand energysaving.Thescrapistwo pieces of steel.
4.Hydraulic pump and cylinder unnecessary for cost saving.
MAP-60
SYD-35不銹鋼水盆開孔器SYD-35StainlessSteelBasinPuncher
?
功能說明
鐵鋁板厚：1.5-3mm
不銹鋼板厚：1.5mm-2mm
噸位：12T
喉深：100mm
重量：12.5kg
模具配置：Φ26mm-35mm
注：出廠已配CP-180泵浦
FUNCTION
Ironaluminum plate thickness:1.5-3mm
Stainlesssteel plate thickness:1.5mm-2mm
Tonnage:12T
Throat depth:100mm
Weight:12.5kg
Mold configuration:Φ26mm-35mm
Note:The factory is equipped with CP-180 pump
圓模及方模Rounddieandsquaredie
功能說明
1.閘刀式剪刀的特點就是比剪刀式的剪刀不易卡住。
2.不需要設定時間。
3.所有刀片都容易更換。
4.180度旋轉頭部使得不同的剪切位置都容易。
FUNCTION
1.Guillotine type cutters feature less jamming than shear type cutters
2.No set-up time required
3.All bladesareeasilyreplaceable.
4.180degree rotatable headsalloweasycutting position.
| 型号 Model | 出力 Output (T) | 长度 Leight (mm) | Wirerope | 圆金属棒 RoundBar (mm) | 绞钢线 Wire Strands (mm) | 电缆 Cable (mm) | ||||||||||||
| 6×7 hemp- core | 6×12 core | (mm) hemp- | 6x19 Soft hemp- core bar | Soft Copper | alumi- bar | Soft steel cing bar | Reinfor-Bare | Bare copper strands | Alumi- | ACSR1×7 | 1×19 guysteel guysteel | Tel- phone | Lead | Under sheathed ground cable | ||||
| CPC-20A | 4 | 420 | 16 | 20 | 20 | 20 | bam 16 | 16 | 13 | 20 | strands 20 | 21 | wtrands 15 | wirands 16 | Cabpe 二 | Crepgtone | 18 | |
| CPC-30A | 7 | 500 | 二 | 二 | 二 | 12 | 14 | 10 | 8 | 25 | 19 | 二 | 二 | 30 | 二 30 | 30 | ||
| CPC-40A | 7 | 580 | 20 | 25 | 25 | 20 | 22 | 16 | 13 | 32 | 25 32 | 40 | 20 | 20 | 二 | 二 | 40 | |
| CPC-24A | 8 | 475 | 18 | 24 | 24 | 24 | 18 | 20 | 16 | 24 | 24 | 24 | 20 | 20 | 24 | 24 | 24 | |
| CPC-55A | 7 | 625 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 55 | 15 | 19 | 55 | 55 | 55 | |
| CPC-65A | 8 | 625 | - | - | - | - | - | - | - | - | 60 | 15 | 20 | 65 | 65 | 65 | ||
Gaution: 1.Cuting of P.C wire or piano wire is prohibited. 2.Stay within themaximum cuting capacity of each tool. 3.Do not pump with more than maximum handle load of each tool.
功能說明
1.剪切頭部可以快速剪切，分體操作。
2.所有裝置都可以通過最大油壓為700kgf/cm2(10000psi)的任
何液壓泵來驅動。
3.所有的裝置都配有PT3/8"的高壓接頭。
4.PT-NPT連接器需要配NPT3/8"牙的快速接頭。
FUNCTION
1.Cutting heads provide fast cutting with remote operation.
2.All unitscan be operated byany hydraulic pumpwith the maximumoil pressure
of 700kgf/cm2(10000psi)
3.All units are equipped with PT 3/8" high pressure couplers.
4.PT-NPTadaptersareavailable on request for NPT3/8" treaded couplers.
| 型号 Model | 出力 Output (T) | 长度 Leight (mm) | Wire rope | 圆金属棒 Round Bar (mm) | 绞钢线 Wire Strands (mm) | 电缆 Cable (mm) | ||||||||||||
| 6×7 hemp- | 6×12 | (mm) hemp- | 6×19 Soft hemp- | Soft Copper | alumi- | Soft steel cing | Reinfor-Bare | Bare corands | Alumi- | ACSR1×7 | 1×19 wiystel guysteel | Tel- | Lead | Under | ||||
| CPC-50 | 7 | 570 | 二 | 二 | - | bar - | - | 二 | - | strands - | - | strands - | strands 二 | CCP | cable) | |||
| CPC-85 | 8 | 650 | - | - | 二 | 二 | - | 二 | 50 85 | 50 | 50 | |||||||
| 4 | 420 | 16 | 20 | 20 | 二 20 | 二 16 | 16 | 二 13 | - 20 | 20 | - 21 | 15 | 16 | 二 | 85 | 85 18 | ||
| CPC-20AF CPC-30AF | 7 | 500 | 二 | 二 | 二 | 12 | 14 | 10 | 8 | 25 | 25 | 19 | - | 二 | 30 | 二 30 | 30 | |
| CPC-50FR | 8 | 660 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 50 | 15 | 20 | 50 | 50 | 50 | |
| HT-40A | 7 | 650 | 20 | 25 | 25 | 25 | 20 | 20 | 16 | 25 | 28 | 18 | 20 | 40 | 40 | 40 | ||
53 JIMU TOOLS
海國 阿灸
| 型号 Model | 出力 Output (T) | 长度 Leight (mm) | Wirerope | 圆金属棒 RoundBar （mm) | 绞钢线 Wire Strands （mm) | 电缆 Cable (mm) | ||||||||||||
| 6×7 hemp- core | 6×12 hemp- core | (mm) 6×19 core | Soft hemp- bar | Soft Copper alumi- | Soft steel bar | cing bar | Reinfor-Bare copper | Bare Alumi- strands | ACSR | 1×7 | 1×19 guysteelguysteel | Tel- phone | Lead | Under sheathed ground cable | ||||
| CPC-45FR | 7 | 655 | 二 | 二 | 二 | 25 | bum 27 | 21 | 18 | 37 | strands 37 | 45 | wirands 25 | wirands 25 | cable 45 | |||
| CPC-55FR | 7 | 660 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 54 | 15 | 20 | 55 | 45 55 | 45 55 | |
| CPC-65FR | 8 | 665 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 60 | 18 | 22 | 65 | 65 | 65 | |
| CPC-85FR | 8 | 710 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 54 | 15 | 20 | 85 | 85 | 85 | |
| HT-50A | 7 | 650 | 20 | 25 | 25 | 25 | 20 | 20 | 16 | 25 | 25 | 45 | 18 | 20 | 50 | 50 | 50 | |
| CPC-75 | 7 | 615 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 75 | 75 | 75 | |||||
| CPC-85 | 8 | 650 | - | - | 二 | 二 | - | 二 | 二 | 二 | 二 | - | 85 | 85 | 85 | |||
功能說明
1.剪切頭部可以快速剪切，分體操作。
2.所有裝置都可以通過最大油壓為700kgf/cm2(10000psi)的任
何液壓泵來驅動。
3.所有的裝置都配有PT3/8"的高壓接頭。
4.PT-NPT連接器需要配NPT3/8"牙的快速接頭。
FUNCTION
1.Cutting heads provide fast cuttingwith remote operation.
2.All units can be operated byany hydraulic pumpwith the maximum oil pressure
of 700kgf/cm2(10000psi)
3.All unitsare equipped with PT 3/8"high pressure couplers.
4.PT-NPTadaptersareavailable on request for NPT3/8"treaded couplers.
| 型号 Model | 出力 Output (T) | 长度 Leight (mm) | Wirerope | 圆金属棒 RoundBar (mm) | 绞钢线 Wire Strands (mm) | 电缆 Cable (mm) | ||||||||||||
| 6×7 hemp- | 6×12 hemp- core | (mm) 6×19 hemp- core | Soft bar | Soft Copper alumi- | Soft steel bar | Reinfor- cing | Bare copper | Bare Alumi- | ACSR | 1x7 | 1×19 guysteelguysteel | Tel- phone | Lead sheathed | Under ground | ||||
| CPC-20H | 4 | 180 | 16 | 20 | 20 | 20 | bam 16 | 16 | 13 | strandsStrands 20 | 20 | 21 | Wtrands 15 | wtirands 16 | cable | 18 | ||
| CPC-30H | 7 | 350 | - | 二 | 12 | 14 | 10 | 8 | 二 | 二 30 | 二 30 | 30 | ||||||
| CPC-40H | 7 | 380 | 22 | 25 | 25 | 20 | 22 | 16 | 13 | 25 32 | 25 32 | 19 40 | 20 | 20 | 二 | 40 | ||
| CPC-24H | 8 | 245 | 18 | 24 | 24 | 24 | 18 | 20 | 16 | 24 | 24 | 24 | 20 | 20 | 24 | 二 24 | 24 | |
| CPC-85H | 4.5 | 400 | - | 二 | 二 | - | - | - | - | 28 | 46 | 二 | 二 | 二 | 85 | 85 | 50 | |
| CPC-100 | 7.5 | 560 | 二 | 二 | 二 | 二 | 二 | 42 | 46 | 二 | 二 | 二 | 100 | 100 | 75 | |||
| CPC-130 | 10 | 650 | 二 | 1 | 二 | 二 | 二 | 1 | 46 | 55 | 1 | 二 | 二 | 130 | 130 | 130 | ||
| CPC-55H | 7 | 410 | - | - | - | - | - | - | - | - | - | 54 | 15 | 20 | 55 | 55 | 55 | |
55 JIMU TOOLS
| 型号 Model | 出力 Output (T) | 长度 Leight (mm) | Wirerope | 圆金属棒 RoundBar (mm) | 绞钢线 Wire Strands （mm) | ||||||||||||
| 6×7 hemp- core | 6x12 hemp- core | (mm) 6×19 hemp- core | Soft Copper bar | Soft alumi- | Soft steel bar | cing bar | Reinfor-Bare copper strands | Bare Alumi- | ACSR | 1×7 | 1×19 guysteel guysteel | Tel- phone | Lead sheathed | (mm) Under ground | |||
| CPC-65KH | 7 | 550 | 二 | 二 | 二 | 二 | bum 二 | 二 | 二 | 二 | strands | strands 二 | wirands 二 | cable 65 | Creopgtone 65 | ||
| CPC-85KH | 8 | 630 | - | - | - | - | - | - | - | - | 二 二 | 二 - | - | - | 85 | 85 | 65 85 |
| CPC-105KH | 10 | 670 | 二 | 二 | 二 | 二 | - | 二 | 二 | 二 | - | 105 | 105 | 105 | |||
| CC-50B | 12 | 330 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 50 | 50 | 50 |
| CPC-120KH | 12 | 690 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 120 | 120 | 120 |
| CC-50C | 10 | 325 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 二 | 50 | 50 | 50 |
| CPC-160 | 13 | 600 | 二 | - | 二 | 二 | 二 | 二 | 二 | 二 | 160 | 160 | 160 | ||||
鍛造刀刃，壽命長，剪切容易高強度鋁合金手柄注意不能用于剪切鋼絲繩和銅硬拉線
Forged knife edge for long shelf life and easy cutting.
Highstrength alalloy handles.
Note: Cutting steel rope and hard drawn copper wiresare prohibited.
| 型号Model | CC-100L | CC-250L | CC-500L |
| 长度Length | 280mm | 600mm | 810mm |
| 重量Weight | 0.6kg | 1.7kg | 2.76kg |
| 剪切范围Cutting Rnge | 铜铝Cu/Al Calbe Max.100mm² | 铜铝Cu/Al Calbe Max.250mm² | 铜铝Cu/Al Calbe Max.500mm² |
| 型号Model | SCC-60 | SCC-100 | SCC-200 |
| 长度Length | 280mm | 600mm | 810mm |
| 重量Weight | 0.6kg | 1.7kg | 2.76kg |
| 剪切范围Cutting Rnge | 钢丝绳Steel Rope7mm 铜线Cu Cable 60mm² | 钢丝绳Steel Rope10mm 铜线Cu Cable 100mm² | 钢丝绳Steel Rope14mm 铜线Cu Cable150mm² |
| Model:HS-125 | |
| 长度Length | 300mm |
| 重量Weight | 0.7kg |
| 剪切范围Cutingrange125mm以下 | 125mmorbelow. |
| Model:HS-250 | |
| 长度Length | 600mm |
| 重量Weight | 1.5kg |
| 剪切范围Cuttingrange250mm以下 | 250mmorbelow. |
八
| Model:HS-500 | |
| 长度Length | 800mm |
| 重量Weight | 2.8kg |
| 剪切范围Cuttingrange500mm以下 | 500mm²orbelow. |
| Model:CC-325 | |
| 长度Length | 260mm |
| 重量Weight | 0.7kg |
| 剪切范围Cuttingrange240mm以下 | 240mm²orbelow. |
1
| Model:CC-400 | |
| 长度Length | 360mm |
| 重量Weight | 1.25kg |
| 剪切范围Cutting range | 400mm以下 400mm²orbelow. |
| Model:CC-500 | |
| 长度Length | 410mm |
| 重量Weight | 1.63kg |
| 剪切范围Cuttingrange500mm以下 | 500mm2orbelow. |
田三
? 二
| ModeI:J13棘轮剪RATCHETCABLECUTTER | Model:J52棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cutting range:钢绞线或是钢芯铝绞线Cutting off steelwire ropes | 剪切范围Cuttingrange:铜铝芯铠装电缆CuttingoffCU/ALamoured cable |
| smallerthan150mmandACSRsmallthan720mm² | smaller than50mm |
| 重量Weight: 1.5kg | |
| 包装Package: | 重量Weight: 2.2kg 包装Package: |
| 帆布袋Fabric bag 尺寸Size 350(510)×120×45mm | 帆布袋Fabric bag 尺寸Size 375(540)×150×40mm |
Co ?
| Model:J3O棘轮剪RATCHETCABLECUTTER | Model:J5O棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange:钢绞线或是钢芯铝绞线Cuttingoff steelwire ropes | 剪切范围Cuttingrange：剪切1440平方以下钢芯铝绞线 |
| smallerthan100mmandACSRsmallthan630mm2 | Cut1440squarefeetbelowtheACSR |
| 重量Weight: 3.5kg | 重量Weight: 3.8kg |
| 包装Package: 帆布袋Fabric bag | 包装Package: 帆布袋Fabric bag |
| 尺寸Size 400(580)×160×60mm | 尺寸Size 350(510)x120x45mm |
二
O人
| Model:J4O棘轮剪RATCHETCABLECUTTER | Model: J75棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cutting range:钢铝芯铠装电缆，1000对通信电缆cuting offCU/AU amoured | 剪切范围Cuttingrange:钢铝芯铠装电缆，3600对通信电缆cutigoffCU/AU amouredcable |
| cablesmaller than300mm2and10o0pairsof communicationcables | smaller than3x120mm2and 3600pairs of communicationcables |
| 重量Weight: 1kg | 重量Weight: 3.5kg |
| 包装Package: 帆布袋Fabric bag | 包装Package: 帆布袋Fabric bag |
| 尺寸Size 330x120x35mm | 尺寸Size 420(600)x200x55mm |
59 JIMU TOOLS
銀行份 廣
| ModeI:J1OO棘轮剪RATCHETCABLECUTTER | Model:J95棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange:铜铝芯铠装电缆CuttingoffCU/ALamoured cable | 剪切范围Cuttingrange：剪断3x185mm及直径95mm以下铜铝铠装电缆 |
| smallerthan3x300mm2or100mm | Cut3x185mm2anddiameter95mmfollowingcopperandaluminumcorearmored cable |
| 重量Weight: 6.5kg | |
| 重量Weight: 5.5kg | |
| 包装Package: 帆布袋Fabric bag 尺寸Size 480(660)x250x50mm | 包装Package: 帆布袋Fabric bag 尺寸Size 610x270x65mm |
1
| Model:J130棘轮剪RATCHETCABLECUTTER | Model:J160棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange：剪断直径130mm以下铝铜芯铠装电缆 | 剪切范围Cuttingrange:剪断直径160mm以下铜铝铠装电缆，6x300mm铜铝铠装电缆线 |
| Cutthediameterof130mmbelowthealuminumcoppercorearmoredcable | Ccthedliameternolowigoperandaluminuamoredablex0m |
| 重量Weight: 8.5kg | |
| 包装Package: 帆布袋Fabric bag | 重量Weight: 12kg |
| 尺寸Size 524（693)x328x59mm | 包装Package: 帆布袋Fabricbag 尺寸Size 560(730)x390x530mm |
| ModeI:XLJ-D-300棘轮剪RATCHETCABLECUTTER | ModeI:XLJ-D-500棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange:40或300mm以下铜铝电缆的切断 | 剪切范围Cuttingrange：剪断500mm以下铜铝电缆 |
| 40or 30omm²followingcopperandaluminumcable cutoff | Cutoff the followingcopperandaluminumcable500mm² |
| 1.0kg | |
| 重量Weight: 帆布袋Fabric bag | 重量Weight: 1.2kg |
| 包装Package: 尺寸Size 235x136x44mm | 包装Package: 帆布袋Fabric bag 尺寸Size 310(235)x136x44mm |
5 1
| ModeI:XLJ-D-50OB棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cutingrange：适用于600mm以下铜芯铝绞线、32mm以下钢芯电缆、 100mm以下钢绞线Φ12mm以下钢筋的切断、Φ8-16钢丝绳的切断 |
| Applicabletothefollowing6o0mm²coppercorewire，32mmfollowingsteelcorecable， 100mm²belowthestrand12mmthefollowing cutoffthesteel,8-16wireropecutoff |
| 重量Weight: 1.9kg |
| 包装Package: 帆布袋Fabric bag |
| 尺寸Size 310(420)x136x45mm |
| Model:XLJ-65A棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange：Φ65或650mm以下铜铝铠装电缆的切断 |
| Φ65or65ommfollowingcopperandaluminumarmoredcablecutoff |
| 重量Weight: 3.0kg |
| 包装Package: 帆布袋Fabricbag |
| 尺寸Size 355x206x70mm |
二
二
| ModeI:XLJ-75A棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange:Φ75以下铜，铝铠装电缆的切断 |
| 75following copper,aluminumarmoredcablecutoff |
| 重量Weight: 3.1kg |
| 包装Package: 帆布袋Fabricbag |
| 尺寸Size 355(435)x206x75mm |
| ModeI:XLJ-95A棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange:1000mm以下或者外径Φ95以下铜、铝铠装电缆的切断 |
| 1000mm²orbelowtheouterdiameterΦ95belowcopper,aluminumarmoredcablecutoff |
| 重量Weight: 6.3kg |
| 包装Package: 帆布袋Fabricbag |
| 尺寸Size 530(725)x270x80mm |
D N
| ModeI:XLJ-10OA棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange:100mm以下的铜铝芯电缆和铠装电缆 |
| 100mm following copperandaluminumcorecableandarmored cable |
| 重量Weight: 6.8kg |
| 包装Package： 帆布袋Fabric bag |
| 尺寸Size 550(730)x280x80mm |
| Model:XLJ-120A棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange:1200mm以下或者外径Φ120以下铜、铝铠装电缆的切断 |
| 1200mm²orbelowtheouterdiameter120belowcopper,aluminumarmoredcablecutoff |
| 重量Weight: 7kg |
| 包装Package: 帆布袋Fabricbag |
| 尺寸Size 555(745)x325x80mm |
61JIMU TOOLS
二
| Model:XLJ-130A棘轮剪RATCHETCABLECUTTER | Model:XLJ-160A棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange：Φ130以下铜，铝铠装电缆的切断 | 剪切范围Cuttingrange：铜铝电缆Φ160mm以下、铠装电缆140以下。 |
| 130followingcopper,aluminumarmored cablecutoff | |
| CopperandaluminumcableΦ160mmbelow，armoredcable140below | |
| 重量Weight: 15kg | 重量Weight: 16kg |
| 包装Package: 帆布袋Fabric bag 尺寸Size 600(750)x325x80mm | 包装Package: 帆布袋Fabricbag 尺寸Size 630(780)x380x90mm |
L 二
| Model:XLJ-G-40棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange：120mm2以下钢绞线800mm以下钢芯线36以下钢芯电缆 |
| 120mm²belowthesteelwire8oommbelowthesteelcore36belowthesteelcorecable |
| 重量Weight: 2.6kg |
| 包装Package: 帆布袋Fabricbag |
| 尺寸Size 350(450)x120x35mm |
| Model:XLJ-G-6O棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange:150mm2以下的钢绞线的切断，1200mm2以下的钢芯铝绞线 的切断，Φ52以下钢芯电缆的切断，Φ16以下低碳元钢的切断 |
| 150mm²belowthecutoffthesteelstrand，12oomm²belowthesteelcorealuminumwirecutoff, 52belowthesteel corecablecutoff,16belowthe lowcarbonsteel cutoff. |
| 重量Weight: 7.0kg |
| 包装Package: 帆布袋Fabric bag |
| 尺寸Size 525(715)x230x80mm |
9f
川
| ModeI:J4OA棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange：剪断300mm以下铜铝电缆 |
| Cutthefollowing3oomm²copperandaluminumcable |
| 重量Weight: 1.1kg |
| 包装Package: 帆布袋Fabric bag |
| 尺寸Size 215x130x45mm |
| ModeI:XLJ-S-240棘轮剪RATCHETCABLECUTTER |
| 剪切范围Cuttingrange:240平方以下铜铝电缆和外径6毫米以下的低碳元钢切断 |
| 240square feetbelowthecopperandaluminumcableanddiameterof6mm belowthelowcarbonsteelcutoff |
| 重量Weight: 2.6kg |
| 包装Package: 帆布袋Fabric bag |
| 尺寸Size 400(555)x95x38mm |
功能說明
1.當螺絲生銹時，這個螺絲破切器是最有效的工具。
2.獨特的帶角度的頭部，允許直接接觸工件。
3.單程，彈簧回油油缸。
4.用途包括：服務型卡車，管道行業，油箱清洗，汽化工廠，鋼
鐵工程及礦山。
5.選擇適當?shù)囊簤罕媒M成液壓泵系列。
FUNCTION
1.When the nuts get rusts,this nut cuting machine is most time.
2.Unique angled head allows flush access.
3.Single-acting,spring return cylinder.
4.Applications include servicing trucks，piping industry，tank cleaning,
petrochemical,steel construction and mining.
5.Select suitable hydraulic pump form hydraulic pumps series.
| 型号 Model | 螺钉范围 BoltRange (mm) | 六角螺母范围 NutRange (mm) | 工作能力 Output (ton) | 行程 Stroke (mm) | 重量 Weight (kg) |
| YP-24 | M8-M16 | 14-24 | 12 | 20 | 3.6 |
| YP-24A | M8-M16 | 14-24 | 10 | 20 | 3.3 |
| YP-24B | M8-M16 | 14-24 | 12 | 20 | 4.0 |
| EP-2432A | M16-M24 | 24-32 | 12 | 32 | 6.5 |
| YP-27 | M22-M27 | 32-41 | 16 | 27 | 8.3 |
| 产品名称 | 型号 | 范 (mm) | 六角螺母范围 (mm) | 工作能力 | eight |
| 螺母破切器系列 | NC-1319 | M6-M12 | 13-19 | (ton) 5 | （kg) 1.2 |
| NC-1924 | M12-M16 | 19-24 | 10 | 2.0 | |
| NC-2432 | M16-M22 | 24-32 | 15 | 3.0 | |
| NC-3241 | M22-M27 | 32-41 | 20 | 4.4 | |
| NC-4150 | M27-M33 | 41-50 | 35 | 8.2 | |
| NC-5060 | M33-M39 | 50-60 | 50 | 11.8 | |
| NC-6075 | M39-M48 | 60-75 | 90 | 34.1 |
功能說明
液壓鋼筋切斷器是最新研制的高精度液壓切斷工具，改變了之前老款的工作效率，攜帶方便，外形美觀，剪切效率高，受力面積小等特點，是建筑、工廠、礦山等單位的理想工具，深受廣大用戶的喜愛。
FUNCTION
Hydraulic steel cuting device is the latest development of high-precision hydraulic cuting tool,changing the old paragraph before thework eficiency, easy tocarryeautifulappearance,highearefficency,mallforcereatc., isthe construction,factories,minesand otherunits ldeal tool,loved by the majority of users.
| 型号 Model | 出力 Output (T) | 剪切范围 Cutting Range (mm) | 行程 RamStroke (mm) | 尺寸 Size (mm) | 重量 Weight （kg) |
| SC-12 | 6 | Φ4-Φ12 | 13 | 305×100×55 | 1.6 |
| SC-16 | 8 | ①4-Φ16 | 17 | 415×125×65 | 2.8 |
| SC-22 | 12 | Φ4-Φ22 | 22 | 505×125×80 | 4.8 |
| SC-25 | 16 | Φ4-Φ25 | 25 | 525×130×85 | 7.3 |
| YQ-16B | 8 | Φ4-Φ16 | 17 | 415×125×65 | 2.8 |
| YQ-22B | 14 | Φ4-Φ22 | 22 | 505×125×80 | 5.0 |
| YQ-27 | 17 | Φ4-①27 | 28 | 560×140×90 | 8.5 |
| YQ-32 | 20 | Φ4-Φ32 | 32 | 600×150×95 | 9.5 |
| SC-16F | 8 | Φ4-Φ16 | 17 | 210×125×65 | 1.3 |
| SC-25F | 16 | Φ4-Φ25 | 25 | 320×130×85 | 4.5 |
| Model:RC-16Forcuttingsteelrope | |
| 剪切范围Cutting range | 4-Φ16mm |
| 电压Voltage | 110V/60Hz |
| 出力Output | 1.05kw |
| 长度Length | 460mm |
| 重量Weight | 12.5kg |
| 包装Package | 铁箱steel case |
| Model:RC-20Forcuttingsteel rope | |
| 剪切范围Cutting range | Φ4-Φ20mm |
| 电压Voltage | 110V/50Hz |
| 出力Output | 1.05kw |
| 长度Length | 460mm |
| 重量Weight | 12.5kg |
| 包装Package | 铁箱steel case |
| Model:RC-22Forcuttingsteel rope | |
| 剪切范围Cutting range | Φ4-Φ22mm |
| 电压Voltage | 110V/60Hz |
| 出力Output | 1.6kw |
| 长度Length | 550mm |
| 重量Weight | 21.5kg |
| 包装Package | 铁箱steel case |
| Model:RC-25 Forcuttingsteel rope | |
| 剪切范围Cutting range | 4-Φ25mm |
| 电压Voltage | 210V/560Hz |
| 出力Output | 1.05kw |
| 长度Length | 460mm |
| 重量Weight | 32kg |
| 包装Package | 铁箱steel case |
山#
| Model:NRC-22Forcuttingsteel rope | |
| 剪切范围Cutting range | Φ4-Φ22mm |
| 电压Voltage | 110V/60Hz |
| 出力Output | 1.05kw |
| 长度Length | 460mm |
| 重量Weight | 18.3kg |
| 包装Package | 铁箱steelcase |
| Model:RC-16BForcuttingsteel rope | |
| 剪切范围Cutting range | Φ4-Φ16mm |
| 电压Voltage | 18V |
| 出力Output | 1.4kw |
| 长度Length | 400mm |
| 重量Weight | 14kg |
| 包装Package | 铁箱steel case |
| Model:RB-16 Forbendingsteel rope | |
| 弯曲范围Bending range | Φ4-16mm |
| 电压Voltage | 110V/60Hz |
| 出力Output | 1.05kw |
| 长度Length | 670mm |
| 重量Weight | 16.5kg |
| 包装Package | 铁箱steel case |
| Model:RB-25Forbendingsteel rope | |
| 弯曲范围Bendingrange | Φ4-25mm |
| 电压Voltage | 110V/50Hz |
| 出力Output | 1.6/1.7kw |
| 尺寸Size | 450×500×440mm |
| 重量Weight | 91kg |
| 包装Package | 木箱Woodencase |
| Model:RB-32 Forbending steel rope | |
| 弯曲范围Bendingrange | Φ6-Φ32mm |
| 电压Voltage | 110V/60Hz |
| 出力Output | 1.6/1.7kw |
| 尺寸Size | 600×500×450mm |
| 重量Weight | 110kg |
| 包装Package | 木箱Woodencase |
67 JIMU TOOLS
功能說明
1.適用一般水管、導線管、瓦斯管、厚鋼管等，角度彎曲90°
2.1/2"-2"一次成形90°，2-1/2“-4”必須移動管子彎曲5次才能
達彎曲弧度。
3.采用堅固的球墨鑄鐵彎管模材質。
4.彎曲平滑、不會造成皺痕，操作方便。
FUNCTION
1.lt is designed for common water pipe,conductor pipe,gas pipe,thick steel pipe, etc.The bending angle could be 90 degree.
2.For 1 / 2 ^ { \dprime } -2"one operationto be 90degree.For2-1/2"-4",pipemustbemoved and bend for five time to the demanded radian.
3.lt is made of strong nodular cast iron bending pipe mould material.
4.Bended surface smooth without folding marking.It's easy to operate.
| 型号 Model | 出力 Output (T) | 行程 Stroke (mm) | 使用范围ApplicableRange(mm) | 所需油量 Oil Capacity (cc) | 重量 Weight (kg) | 体积 Volume (cm) | |||
| 薄钢管 Thin-steel conduit (A) | 厚钢管 Thick-steel conduit(B) | 瓦斯管 GasPipe (SGP) | |||||||
| SWG-2A | 16 | 250 | 15.9mm-520.8m (5/8") | 21mm-59.6mm | 21.2mm-20152m | 680 | 60 | 73×32×20 | |
| SWG-3B | 18 | 320 | 15.9mm-76.2mm | 21mm-87.9mm | 1/2mm-82.1mm | 990 | 125 | 92×40×23 | |
| SWG-4C | 20 | 415 | 15.8mm-76.2mm | 21mm-103.4mm | 21.7mm-14.3mm | 1300 | 200 | 118×46×25 | |
功能說明
1.適用一般水管、導線管、瓦斯管、厚鋼管等，角度彎曲90°
2 . 1 1 2 " - 2 " 一次成形90°，2-1/2“-4”必須移動管子彎曲5次才能達彎曲弧度。
3.采用堅固的球墨鑄鐵彎管模材質。
4.彎曲平滑、不會造成皺痕，操作方便。
5.單孔式與復動式油壓缸，復動式必需配雙回路泵浦CTE-25AD。6.油管接頭配PT3/8"牙。
FUNCTION
1.It is designed for common water pipe,conductor pipe,gas pipe,thick steel pipe, etc.Bending angle could be 90 degree.
2.For 1 1 2 ^ { \circ } - 2 ^ { \circ } one operation to be 90 degree.For2-1/2"-4",pipemust be moved and bend for five time to the demanded radian.
3.It is made of strong nodular cast iron bending pipe mould material.
4.Bended surfacesmoothwithout foldingmarking.Operateconveniently.
5.Single holeand dual active cylinder:Dual active style must work with double loop pump CTE-25AD.
6.Oil pipe coupling fited with PT3/8"thread.
| 型号 Model | 出力 Output (T) | 行程 Stroke (mm) | 使用范围ApplicableRange(mm) | 所需油量 Oil Capacity (cc) | 重量 Weight (kg) | 体积 Volume (cm) | |||
| 薄钢管 Thin-steel conduit (A) | 厚钢管 Thick-steel | 瓦斯管 GasPipe | |||||||
| CPB-2 | 16 | 250 | 15.9mm-50.8mm | conduit(B) 21mm-59.6mm | (SGP) 21.7mm-20.5m | 680 | 52 | 73×32×20 | |
| CPB-3 | 18 | 270 | 15.9mm-76.2mm | 21mm-87.9mm | 1.2mm-(2.1m | 990 | 108 | 92×40×23 | |
| CPB-4 | 20 | 270 | 15.8mm-76.2mm | 21mm-143.4mm | 21.7mm-14.3mm | 1300 | 190 | 118×46×25 | |
| 型号 Model | 出力 Output | 中心轴行程 Centeraxistravel | 横向最大拉距 Horizontal maximum | 纵向最大拉距 Vvertucal maximum | 爪子长度 Claw length | 重量 Weight |
| YLX-5T | 5T | 50mm | 200mm | 140mm | 200mm | 8kg |
| YLX-10T | 10T | 60mm | 250mm | 160mm | 250mm | 10.5kg |
| YLX-20T | 20T | 70mm | 350mm | 195mm | 300mm | 16kg |
71 JIMU TOOLS
CK整體式液壓拉馬
Integral-UnitHydraulic GearPullerCK
| 号l | Rate output | Max. | Weight | Votum | |
| CK-5 | 5 | 200 | 50 | 7.5 | (1/4)44×38×32 |
| CK-10 | 10 | 250 | 50 | 11 | (1/2)44×21×36 |
| CK-20 | 20 | 350 | 60 | 19 | 43×40×14 |
| CK-30 | 30 | 400 | 60 | 25 | 48×20×18 |
| CK-50 | 50 | 500 | 60 | 45 | 52×25×22 |
EP分體式液壓拉馬
Split-Unit Hydraulic Gear Puller EP
功能說明
1.利用新型油壓拔輪工具，操作輕而易舉。
2.一般傳統式拔輪，使用起來較費力。
3.可以自由旋轉，依拔輪距離活塞中心點，很快可碰到被拔的中心點。
4.30ton以上的油缸必須配大油量的油泵，如CP-700-2A。
5.油管接頭配PT3/8"牙。
FUNCTION
1.The new type of oil pressure pull wheel tool adopted for easy operation.
2.Traditional ordinarypull wheel leading to great effort needed.
3.Freely rotate. Upon the center point from pull wheel to piston,the center point to be pulled is easily met.
4.The cylinder in 30ton orabove must be assembled with large oil tank pump.For example, CP-700-2A.
5.Oil pipe coupler fitted with PT 3/8"thread.
| 型号 Model | Output (T) | 最大行 (mm) | 爪数w number | 张距范围 (mm) | 整机重量 (kg) | ve (cm) |
| EP-5 | 5 | 50 | 3 | 50-200 | 15 | 73×18×18 |
| EP-10 | 10 | 50 | 3 | 50-250 | 20 | 73×18×18 |
| EP-20 | 20 | 60 | 3 | 100-350 | 27 | 73×21×18 |
| EP-30 | 30 | 60 | 3 | 150-400 | 35 | 73×25×18 |
| EP-50 | 50 | 60 | 3 | 200-500 | 55 | 73×25×18 |
| EP-100 | 100 | 105 | 3 | 300-600 | 150 | 103×70×23 |
| Model:FSM-8机械式法兰分离器 | |
| 最大分离力Maximum separation force | 8T |
| 尖端厚度Tipthickness | 6mm |
| 最大分距The largest distance | 81mm |
| 重量Weight | 6.5kg |
| Model:FS-14液压法兰分离器 | |
| 吨位Tonnage | 14T |
| 顶部间隙Topclearance | 6mm |
| 最大分离厚度Maximum separation thickness | 81mm |
| 重量Weight | 12kg |
| 尺寸Volume | 310x120x360mm |
功能說明
1.適于維修，檢修、測試和閥門更換應用。
2.整體分離楔概念：無摩擦，平行平常運動。
3.消除法蘭損傷和分離楔損壞的危險。
4.獨特的互鎖楔子設計-第一級無彎曲無滑脫危險。
5.插入口要求尺寸僅為6mm。
6.臺階形張臂的設計使每格臺階可承受滿負荷。
7.較少的運動部件，經久耐用，維護方便。
FUNCTION
1.Suitableformaintenance,overhaul,testing,andvalvereplacementYing Yong.
2.Asawholewedge of the concept of separation:no friction,parallel movement
usually.
3.Toeliminateseparationwedge flange damageand the risk of damage to.
4.Unique interlocking wedge design-first-class non-bending risk of non-slip.
5.Insert laskedmeasuring only 6mm.
6.Stepped Zhang arm design so that each cell can withstand full load step.
7.Less moving parts, durable,easy to maintain.
| Model:FSH-14法兰分离器 | |
| 加工能力WorkingRange | 14T |
| 顶部间隙Topofthegap | 6mm |
| 最大分离厚度Separation of the thickness of the largest | 81mm |
| 分离器类型SeparationType | 液压 |
| 油量Oil | 78mm³ |
| 重量Weight | 7.1kg |
73 JIMU TOOLS
功能說明
輕型宜人的設計易使用。從70-216mm的可調尖端寬度，應用范圍廣。單作用，彈簧回位。
FUNCTION
Lightweight,easytocarryandsimple tooperate.
Thewedgebreadthadjustable from70 to216mm.
Single-acting,spring return.
共
| Model:FS-538法兰破开器 | |
| 吨位Tonnage | 5T |
| 行程Stroke | 38mm |
| 重量Weight | 6kg |
| 体积Volume | 28×25×12cm |
#
| Model:FS-1054法兰破开器 | |
| 吨位Tonnage | 10T |
| 行程Stroke | 54mm |
| 重量Weight | 13.5kg |
| 体积Volume | 32×32×15cm |
二
| Model:YQ-30整体式液压扩张器 | |
| 吨位Tonnage | 8T |
| 顶部厚度Topthickness | 11mm |
| 最大扩张距离Maximum expansion distance | 30mm |
| 最大张开距离Maximumopeningdistance | 56mm |
| 重量Weight | 3.7kg |
| Model:YQ-55整体式液压扩张器 | |
| 吨位Tonnage | 12T |
| 顶部厚度Topthickness | 13mm |
| 行程Stroke | 25mm |
| 扩开范围Expand thescope | 13-59mm |
| 重量Weight | 7kg |
功能說明
該產品廣泛應用于工程機械、電力、石油、礦山、煤炭、冶金、造紙、建筑、港口、索道等行業，電纜地下通道展放或地面展放，延放電纜及導線，產品分為單輪和三輪，不易損壞電纜。
FUNCTION
The productiswidely used in engineering machinery,electric power,petroleum, mining，coal，metallurgy，papermaking,construction,port,cableandother industries,cable tunnels show exhibition place or on the ground put the extension cableandwirerelease,the product isdivided intosingle-roundand three,non-fragile cables.
| Model:HL-I | |
| 吨位Tonnage | 1000T |
| 滑轮规格Pulley Szie | Φ160×Φ140mm |
| 重量Weight | 4kg |
| 体积Volume | 28×22×18cm |
| Model:HL-IB | |
| 吨位Tonnage | 1000T |
| 滑轮规格PulleySzie | Φ160×140mm |
| 重量Weight | 4kg |
| 体积Volume | 36×25×22cm |
| Model:HL-IlI | |
| 吨位Tonnage | 1000T |
| 滑轮规格PulleySzie | 160×140mm |
| 重量Weight | 11kg |
| 体积Volume | 53×32×33cm |
I L2
| Model:HL-IIIB | |
| 吨位Tonnage | 1000T |
| 滑轮规格Pulley Szie | Φ160×Φ140mm |
| 重量Weight | 12kg |
| 体积Volume | 58×32×18cm |
75 JIMU TOOLS
| Model:ZHL-IIIA | |
| 吨位Tonnage | 1000T |
| 滑轮规格Pulley Szie | Φ160xΦ140mm |
| 重量Weight | 13kg |
| 体积Volume | 53x32x33cm |
功能說明
用于架空電力線路調整弧垂和收緊導線。采用高強度鋁鈦合金材料精鍛成型、自重輕，體積小。適用于鋁絞線和鋼芯鋁絞線。
FUNCTION
Adjustment for overhead power linessagand tightenwire. Using high-strength aluminumalloymaterials,precision forgingshape,lightweight,small size. Applicable to aluminum and ACSR stranding.
| Model:S-1000CL | |
| 额定负荷RatedLoad | 10KN |
| 应用范围 Range of Aplication | 2.5~16的纲绞线铜绞线 $2.5~16oftheClassStranded CopperStranded |
| 重量Weight | 0.8kg |
| Model:S-2000CL | |
| 额定负荷RatedLoad | 20KN |
| 应用范围 Range of Aplication | Φ4~22的纲绞线，钢芯铝绞线，绝缘线 Φ4~22oftheClass strandedwire,ACSR,insulatedwire |
| 重量Weight | 1.3kg |
| Model:S-3000CL | |
| 额定负荷RatedLoad | 30KN |
| 应用范围 Range of Aplication | 16~32的纲绞线，钢芯铝绞线，绝缘线 16 - 32 of the Class stranded wire,ACSR,insulated wire |
| 重量Weight | 1.3kg |
| Model: SLK-1 | |
| 额定负荷Rated Load | 10KN |
| 应用范围 Range of Aplication | 适用导线：LGJ25-70 |
| 重量Weight | 1.1kg |
| Model: SLK-2 | |
| 额定负荷Rated Load | 20KN |
| 应用范围 RangeofAplication | 适用导线：LGJ95-120 |
| 重量Weight | 1.5kg |
| Model: SLK-3 | |
| 额定负荷Rated Load | 30KN |
| 应用范围 Range of Aplication | 适用导线：LGJ150-240 |
| 重量Weight | 2kg |
功能說明
1.用于電力工程，電信工程收緊導地線或牽引設備，打拉線用。2.采用高強度鋼絲，強力不易被拉斷，鉤頭為合金鋼鍛制。且鉤頭部分為橢圓形帶保險裝置，美觀，強度高。3.手柄可360度旋轉，控制卡鈺可倒向旋轉，使用方便。
FUNCTION
1.Usedinpowerengineering，telecommunicationsengineeringoratraction device to tighten the lead ground,playingwith the pull.
2.Using high-strengthsteel wire,not easilypulledoffastrong,forgedalloy steel hook for the system.And the majority of oval-shaped hook witha safety device aesthetics, high strength.
3.Handle can be rotated 360 degrees,the control card can be turned to rotate Civil easy to use.
| 规格 吨 | 钢索直径*长度 毫米mm | 手柄长度 毫米mm | 两钩间最小距离 毫米mm | 净重 公斤 | 箱/台 |
| 2 | 6*1500单根 | 460 | 430 | 4.2 | 6 |
| 规格 吨 | 钢索直径*长度 毫米mm | 手柄长度 毫米mm | 两钩间最小距离 毫米mm | 净重 公斤 | 箱/台 |
| 1.5 | 6*1000单根 | 460 | 430 | 3.9 | 6 |
| 规格 吨 | 钢索直径*长度 毫米mm | 手柄长度 毫米mm | 两钩间最小距离 毫米mm | 净重 公斤 | 箱/台 |
| 1 | 5*1000单根 | 370 | 390 | 3.1 | 6 |
77 JIMU TOOLS
功能說明
1.適用于鋁塑管、PEX管、PB管等與銅管件、銅接頭連接，卡壓
不銹鋼套、銅套、鋁套。
2.液壓系統穩定 \Rightarrow 壓接質量穩定幾乎免維修。
3.剪刀式開口=>壓接作業有最小對墻面尺寸。
4.封壓頭部可以旋轉 \Rightarrow 便利作業角度。
5.自動泄壓裝置=>確保壓接出力。
6.輕巧容易攜帶。
7.雙速進油設計，壓接速度快。
FUNCTION
1.Foraluminum-plastic pipe,PEXpipes,PB pipesand other fitingswith brass, copper connector connection,compression stainless steel sets,coppersleeve, aluminum cover.
2.Stable hydraulicsystemto ensure stablecrimping quality.Maintenance is almost unnecessary.
3.Knife style opening.Crimpingwork could be go to narrowspace.
4.Crimping head couldbe rotated for convenient workingangle.
5.Automatic pressure releaseunite toensure efficient crimping force output.
6.Light weight for easy carrying.
7.Due speed oil input design to ensure fast crimping speed.
| Model:KG-1632液压卡压钳 | |
| 适用范围Application | 不锈钢管12-Φ32mm |
| 出力Output | 12T |
| 行程RamStroke | 22mm |
| 尺寸Size | 480×250×210mm |
| 重量Weight | 7kg |
| Model:FT-50液压卡压钳 | |
| 适用范围Application | 不锈钢管50mm |
| 出力Output | 16T |
| 行程RamStroke | 25mm |
| 尺寸Size | 480×240×220mm |
| 重量Weight | 8kg |
| Model:CW-2540液压卡压钳 | |
| 适用范围Application | PEX，P多管12-63mm |
| 出力Output | 9T |
| 行程RamStroke | 38mm |
| 尺寸Size | 630×200×60mm |
| 重量Weight | 4kg |
| Model:EMT-1632D充电式压管工具BateryPoweredCrimpingPipe Tool | |
| 出力Output | 7T |
| 工作行程RamStroke | 16mm |
| 管件形式ForPEX&MLCP | 16 202632mm |
| 管件形式Forstainlesssteel pipe | 132025mm |
| 电池电压Battery Voltage | 18V |
| 电池容量BatteryCapacity | 3Ah |
| 充电时间Charging Time | 2Hour |
| 产品尺寸Dimension | 340*77*355mm |
| 重量Weight | 5.3kgs |
| 型号 Model | 出力 Output (T) | 适用范围 Application (mm) | 标准配模 StandardMould (mmΦ) | 重量 Weight （kg) |
| EMT-1332K | 7 | 16-32 | 16,20,25,32 | 5.6 |
| EP-1332K | 5.5 | 16-32 | 16,20,25,32 | 3.9 |
| CBS-108K | 7 | 15-50 | 15,20,25,32,40,50 | 6.0 |
分離式液壓卡壓鉗
功能說明
1.適用于屋內外工程，各種壓接角度和狹窄的工作空間。
2.不銹鋼管件專用工具液壓式壓接，六角形設計，不容易脫落。
3.出廠配壓模按國家尺寸，如不同可另訂做。
4.自動泄壓裝置 \Rightarrow 確保壓接出力。
5.輕巧容易攜帶。
6.配合單動式腳踏泵、手動泵、電動泵使用。
7.油管接頭配PT3/8"牙。
Crimping tool forstainless pipe FUNCTION
1.Foraluminum-plastic pipe,PEX pipes,PB pipes and other fitings with brass, copperconnectorconnection,compressionstainlesssteelsets,coppersleeve, aluminum cover.
2.Stable hydraulic system to ensure stable crimping quality.Maintenance is almostunnecessary.
3.Knife style opening. Crimping work could be go to narrowspace.
4.Crimping head could be rotated for convenient workingangle.
5.Automatic pressure release unite to ensure efficient crimping force output.
6.Light weight for easy carrying.
7.Due speed oil input design to ensure fast crimping speed.
| 型号 Model | 出力 Output | 压接范围 ContactMould (mm) | 压接头部 Crimpinghead （mm) | 行程 RamStroke (mm) | 重量 Weight （kg) |
| FT-1525H | (T) 9 | 不锈钢管Φ15-Φ25 | SW15SW20SW25 | 18 | 3 |
| FT-3250H | 16 | 不锈钢管32-50 | SW32SW40SW50 | 25 | 7 |
功能說明
壓接銅管、不銹鋼管及銅管套管，它也用于壓接水管、電氣管及化工管道。
FUNCTION
CrimpthecoppripnssteledoppripedItissoedforimpigteaterpiectricendal
| 型号 Model | 适用范围 Application | 标准配模 StandardMould (mm²) | 尺寸 Size (mm) | 重量 Weight （kg) |
| JT-1632 | 16-32 | 16、20、25、32 | 560mm，可伸至860mm | 2.5 |
| CW-25 | 25 | 25 | 530×140 | 1.8 |
| CW-1626 | 16-26 | 16、20、26 | 490×140 | 1.7 |
| PE-16/20/25/32 | 16、20、25、32 | 16、20、25、32 | 510×140 | 1.5 |
| CW-1626B | 16-26 | 16、20、26 | 60mm,可伸至860mm | 1.9 |
| Model:BP-400PeelingKnife | |
| 适用范围 Pelling Range | Φ30mm以下的铜铝电缆， 剥切深度：4.5mm。 Φ30mmbelow the copperand aluminumcable,strippingdeep Degree:4.5mm. |
| 重量Weight | 0.15kg |
| 尺寸Size | 长度：170mm |
| Model:BK-105PeelingKnife | |
| 适用范围 PellingRange | 直经50-105mm电力电缆外层剥除， 最大厚度为15mmStraightthrough the50-105mmpowercableouter stripping,themaximum thickness of15mm |
| 重量Weight | 1.7kg |
| 尺寸Size | 长度：185mm |
| Model:BXQ-Z-40APeelingKnife | |
| 适用范围 Pelling Range | 剖切的厚度准确可调，适用于导 线，电缆的终端和中间剥线。 适用范围：剥切外径14-40mm， 剥切厚度小于6mm，中段小于4mm Thejustut ticknisacureieiand tionand intermediate stripping. Scope:stripping the outer diameter of14-40mm,strippingthicknessof lessthan6mm,themiddleisless |
| 重量Weight | than4mm 1.04kg |
| 尺寸Size | 275x95x60mm |
1 BX-30S
| Model:BXQ-Z-40B Peeling Knife | |
| 适用ngange | 剖切的厚度准确可调，适用于导 线，电缆的终端和中间剥线。 适用范围：剥切外径14-40mm，剥 切厚度小于6mm，中段小于4mm Scope:stripping the outer diameter of14-40mm,stripping thicknessof lessthan6mm,themiddleisless |
| 重量Weight | than4mm 1.04kg |
| 尺寸Size | 275×95x60mm |
| Model:BX-30SPeelingKnife | |
| 适用范围 PellingRange | 使用范围剥除70-300mm之间的 电缆绝缘层 Use the scope of stripping 70-300mm²between the cable |
| 重量Weight | insulation 0.4kg |
| 尺寸Size | 280x80x55mm |
| Model:PG-5 | |
| 长度Length | 170mm |
| 重量Weight | 0.15kg |
81JIMU TOOLS
| Model:BX-40APeelingKnife | |
| 适用范围 PellingRange | 20-40mm以下电缆主绝缘层剥 除 20-40mm below the cablemain insulation stripping. |
| 重量Weight | 0.8kg |
| 尺寸Size | 250x85x55mm |
| Model:BX-50PeelingKnife | |
| 适用范围 Pelling Range | 适用于70-400平方绝缘导线或电 力电缆线芯末端和中段主绝缘层 的剥除 Applicable to 70-400 square insulationwireor powercable core end and the middle of the main insulation layer stripping |
| 重量Weight | 1kg |
| 尺寸Size | 280×85x50mm |
| Model:BX-40BPeelingKnife | |
| 适用范围 PellingRange | 20-40mm以下电缆半导体层剥 除 20-40mm followingcable semiconductor layerstripping. |
| 重量Weight | 0.8kg |
| 尺寸Size | 250x85x55mm |
| Model:BX-30Peeling Knife | |
| 适用范围 Pelling Range | 适用于70mm平方-300mm平方 （直径Φ15-①30mm之间）绝缘 导线或电力电缆线芯末端和中段 主绝缘层的剥除 Applicable to70mmsquare- 300mmsquare (diameter15- Φ30mm between) insulated wire or power cable core end and the middle of the main insulation layer |
| 重量Weight | stripping 0.8kg |
| 尺寸Size | 245x80x45mm |
大
| Model:KBX-65PeelingKnife | |
| 适用范围 Pelling Range | 剥除直径35-65mm电缆绝缘层及 半导体层，通常适用于35KV电缆 头处理。 Stripped35-65mmdiameter cable insulation and semiconductor layer, usually suitable for 35KV cable head treatment |
| 重量Weight | 1.4kg |
| 尺寸Size | 295x125×70mm |
型號：HS-D1
壓接能力Capacity:0.5-6.0mm2
長度Length:205mm
重量Weight:0.30kg
型號：HS-D2
壓接能力Capacity:0.5-6.0mm2
長度Length:205mm
重量Weight:0.30kg
二 1 SOK E 一$ ce
83 JIMU TOOLS
A
功能說明
壓接鉗用于非焊接的，符合標準的電氣連接，所有零部件都采用特殊鋼制作，經特殊淬火和退火處理，口模頭部磨光處理，壽命特長，依端子大小調整口徑。
FUNCTION
| Model:CT-38 | |
| 应用范围Rangeof Application大型Y.o端子 | |
| 压接能力Capacity | 8-38mm² |
| 美国标准AWG | 8-2 |
| 长度Length | 570mm |
| 重量Weight | 2.2kg |
Thecrimping toolsisused for non-weldingand standardelectrical connection. All the componentsaremadeof special steel,treatedbyspecial quenchingand annealing.The head of the month tool has beenpolished.The tools iswith the characteristicsof longlifeandthediameterofthecrimpingmonthcanbe adjusted according to the size of the terminal.
| Model:CT-80 | |
| 应用范围Range of Application大型Y.o端子 | |
| 压接能力Capacity | 8-80mm |
| 美国标准AWG | 8-3/0 |
| 长度Length | 635mm |
| 重量Weight | 3.2kg |
| Model:CT-150 | |
| 应用范围Range of Application大型Y.o端子 | |
| 压接能力Capacity | 16-150mm |
| 美国标准AWG | 8-250/300MCM |
| 长度Length | 765mm |
| 重量Weight | 5.2kg |
| Model:KH-230 | |
| 应用范围Range of Application裸端子Non-insulated cable links | |
| 压接能力Capacity | 10-240mmAL/CU |
| 美国标准AWG | #4,-#350MCM |
| 长度Length | 980mm |
| 重量Weight | 4.7kg |
| Model:KH-150 | |
| 应用范围Rangeof Application | 裸端子Non-insulated cable links |
| 压接能力Capacity | 10-120mmAL/CU |
| 美国标准AWG | #4,-#120MCM |
| 长度Length | 610mm |
| 重量Weight | 3.1kg |
| Model:JT-300 | |
| 压接范围Crimpingrange | 16-300mm |
| 压接形式Crimpingtype | 六角hexagon |
| 长度Length | 595(875)mm |
| 重量Weight | 4.0kg |
| 包装Package | 塑料盒plastic case |
| 附件Accessories | 16,25,35,50095,12050,15240 |
功能說明
1.裸端子專用（壓后呈六角形）2.壓接鉗用于非焊接的，符合標準的電氣連接，精密的口模材質為SCM-40超硬工具鋼制造而成，壽命特長，孔徑尺寸精確，壓著效果佳。
FUNCTION
1.For non-insulated cable links. 2.The crimping tools is used for non-welding and standard electrical connection.The mouldof jawismadeofSCM-40 hardest tool steel.Itiswiththecharacteristicsof long life,accurate borediameterand good crimpingeffect.
| Model:JY-0650A | |
| 应用范围Range of ApplicationY.O裸端子Non-insulated cablelinks | |
| 压接能力Capacity | 6-50mm² |
| 长度Length | 390mm |
| 重量Weight | 1.3kg |
| Model:JY-25150/JY-70240 | |
| 应用范围 Range ofApplication | 非绝缘端子和连接头 Non-insulated cable links |
| 压接能力Capacity | 25-150mm/70-240mm² |
| 长度Length | 670mm/980mm |
| 重量Weight | 4kg/5.6kg |
| Model:MT-120 | |
| 应用范围Range of Application | 裸端子Non-insulated cable links |
| 压接能力Capacity | 10-120mm² |
| 长度Length | 560mm |
| 重量Weight | 3.5kg |
85 JIMU TOOLS
S0 二 /
| Model:JY-0650 | |
| 应用范围 Range of Application | 非绝缘端子和连接头 Non-insulated cable links |
| 压接能力Capacity | 6-50mm² |
| 长度Length | 385mm |
| 重量Weight | 1.25kg |
| Model:JY-16120 | |
| 应用范围Range of ApplicationY.O裸端子Non-insulated cablelinks | |
| 压接能力Capacity | 16-120mm2 |
| 长度Length | 650mm |
| 重量Weight | 3.8kg |
| Model:MT-150 | |
| 应用范围Rangeof Application | 裸端子Non-insulated cable links |
| 压接能力Capacity | 10-150mm² |
| 长度Length | 570mm |
| 重量Weight | 4kg |
LE HIlaJIMUTOOLSE
用于非焊接的，符合標準的電氣連接，適合管狀裸端子及管狀預絕緣端子。壓接時只要將端子側向進入壓線鉗，根據端子所要求的擠壓力度達到時，強制制動裝置才會使壓接鉗口自動松開，保證在反復壓線時能保持較高質量的壓線標準。由于設定了最佳的握柄位置，以及采用輕便緊湊的結構和符合人體工程學原理的手柄形狀的設計，使操作時減輕了疲勞度。
It isapplicable for tubular bare terminals and pre-insulated terminal on non-welding connectioncompliedwithstandard electrical connection.Whencrimping,the terminal shouldbeputintocrimpingpliers laterally.Thedemandedpressingforcemustbe reachedbefore thebrakeunitautomaticallyrelease the jawof thepliers.Thushighquality crimping standard could be ensured during repeatedly crimping.Due to perfect gripping position fixed and logical and light structure and the handle shape designmeeting human being engineering principle,it reduces fatigue degree.
| Item No: HSC8 6-4 | |
| 应用范围 Rangeof Application | 套管式端子 Wir-end ferrules |
| 压接能力Capacity | 0.25-6.0mm² |
| 美国标准AWG | 23-10 |
| 长度Length | 175mm |
| 重量Weight | 0.36Kg |
設計獨特，輕巧省力；壓緊時，握力可均勻地傳至各個壓線口（4個或6個），由于設計合理，符合力學原理，鉗身僅為175mm，而重量只有360g。
O 二 CRIMPFOXUD6-
The design is unique due to lightweightand saving energy.When crimping tightly,the gripping forcewould evenly transfer toallthe section(6 or6 spots) of crimping terminal. Becauseof reasonabledesigncomplied with human being engineeringprinciple,the weight of the pliers isonly 360g and the lengthof the pliers body isonly175mm.
| ItemNo:HSC86-6 | |
| 应用范围 Rangeof Application | 套管式端子 Wir-endferrules |
| 压接能力Capacity | 0.25-6.0mm2 |
| 美国标准AWG | 23-10 |
| 长度Length | 175mm |
| 重量Weight | 0.36kg |
用于非焊接的，符合標準的電氣連接，適合管狀裸端子及管狀預絕緣端子。壓接時只要將端子側向進入壓線鉗，根據端子所要求的擠壓力度達到時，強制制動裝置才會使壓接鉗口自動松開，保證在反復壓線時能保持較高質量的壓線標準。
It isapplicablefor tubular bare terminalsandpre-insulated terminal on non-welding connection complied with standard electrical connection.When crimping,the terminal shouldbeputintocrimpingpliers laterally.Thedemandedpressingforcemustbe reached before the brake unit automatically release the jawof the pliers.Thus high quality crimping standard could be ensured during repeatedly crimping.
| Item No:HSC8 16-4 | |
| 应用范围 RangeofApplication | 套管式端子 Wir-end ferrules |
| 压接能力Capacity | 6.0-16.0mm² |
| 美国标准AWG | 10-5 |
| 长度Length | 210mm |
| 重量Weight | 0.52Kg |
川川/二
| Model:HS-6L | |
| 应用范围 Rangeof Application | 非绝缘端子及连接头 Non-insulated cable links |
| 压接能力Capacity | 1-6mm² |
| 美国标准AWG | 17-10 |
| 长度Length | 250mm |
| 重量Weight | 0.35kg |
| Model:HS-6M | |
| 应用范围 RangeofApplication | 非绝缘端子及连接头 Non-insulated cable links |
| 压接能力Capacity | 1-6mm² |
| 美国标准AWG | 17-10 |
| 长度Length | 250mm |
| 重量Weight | 0.35kg |
| ItemNo:HD-6 | |
| 应用范围 Range of Application | 非绝缘端子及连接头 Non-insulated cable links |
| 压接能力Capacity | 0.5-6mm² |
| 美国标准AWG | 17-10 |
| 长度Length | 230mm |
| 重量Weight | 0.30kg |
| Model:HD-8L | |
| 应用范围 Rangeof Application | 非绝缘端子及连接头 Non-insulatedcable links |
| 压接能力Capacity | 1.25-8mm² |
| 美国标准AWG | 16-8 |
| 长度Length | 270mm |
| 重量Weight | 0.55kg |
O 二 二 附棘輪裝置，操作輕便，防銹效果好，壓著壽命可達30000次以上。 Fitted with ratchet unit for easy operation and good rust resistant. Crimping shelf lifecould reachto 30oo0 timesorabove.
| Model:HD-14L | |
| 应用范围 Rangeof Application | 非绝缘端子及连接头 Non-insulated cable links |
| 压接能力Capacity | 5.5-14mm² |
| 美国标准AWG | 10-6 |
| 长度Length | 270mm |
| 重量Weight | 0.55kg |
| Model:HD-16L | |
| 应用范围 Range of Application | 非绝缘端子及连接头 Non-insulated cable links |
| 压接能力Capacity | 1.25-16mm2 |
| 美国标准AWG | 16-5 |
| 长度Length | 270mm |
| 重量Weight | 0.55kg |
三/川川
| Model:HX-16 | |
| 应用范围 RangeofApplication | 非绝缘端子及连接头 Non-insulated cable links |
| 压接能力Capacity | 6-16mm² |
| 美国标准AWG | 10-5 |
| 长度Length | 270mm |
| 重量Weight | 0.55kg |
| ItemNo:HD-25L | |
| 应用范围 RangeofApplication | 非绝缘端子及连接头 Non-insulated cable links |
| 压接能力Capacity | 5.5-25mm² |
| 美国标准AWG | 12-4 |
| 长度Length | 354mm |
| 重量Weight | 0.85kg |
| Model:HX-26B | |
| 应用范围 Range of Application | 非绝缘端子及连接头 Non-insulated cable links |
| 压接能力Capacity | 6-25mm² |
| 美国标准AWG | 10-3 |
| 长度Length | 354mm |
| 重量Weight | 0.85kg |
| Model:HD-38L/HD-50L | |
| 应用范围 RangeofApplication | 非绝缘端子及连接头 Non-insulated cable links |
| 压接能力Capacity | 5.5-38mm² |
| 美国标准AWG | 10-2 |
| 长度Length | 356mm |
| 重量Weight | 0.85kg |
| Model:AN-04WFForwireferruleend sleeves | |
| 压接范围Crimpingrange | 1.0-6mm² |
| 压接形式Crimpingtype | 点式Indentcrimping |
| 长度Length | 230mm |
| 重量Weight | 0.6kg |
| 包装Package | 插卡blistercard |
| Model:AP-457 Fornon-insulated terminal | |
| 压接范围Crimpingrange | 0.5-10mm² |
| 压接形式Crimpingtype | 六角hexagoncrimping |
| 长度Length | 250mm |
| 重量Weight | 0.60kg |
| 包装Package | 插卡blistercard |
| Model:HS-02HForCoaxial cable | |
| 压接范围Crimpingrange | 0.5-6mm² |
| 压接形式Crimping type | 六角hexagoncrimping |
| 长度Length | 230mm |
| 重量Weight | 0.60kg |
| 包装Package | 插卡blistercard |
1
| Model:HS-05FL Flagtype receptacles | |
| 压接范围Crimpingrange | 0.5-2.5mm² |
| 压接形式Crimping type | 旗型Flag crimping |
| 长度Length | 230mm |
| 重量Weight | 0.60kg |
| 包装Package | 插卡blistercard |
| Model:HS-05H ForCoaxial cable | |
| 压接范围Crimpingrange | 0.5-10mm² |
| 压接形式Crimpingtype | 六角hexagoncrimping |
| 长度Length | 230mm |
| 重量Weight | 0.60kg |
| 包装Package | 插卡blistercard |
47 八二
| Model:HS-O7FLForFlagtypefemalereceptaclesinsulatedterminals | |
| 压接范围Crimpingrange | 1.25-2.5mm² |
| 压接形式Crimpingtype | 旗型Flag crimping |
| 长度Length | 230mm |
| 重量Weight | 0.6kg |
| 包装Package | 插卡blistercard |
| Model:HS-30J ForNon-InsulatedTerminal | |
| 压接范围Crimpingrange | 0.5-6mm² |
| 压接形式Crimping type | 点式Indentcrimping |
| 长度Length | 230mm |
| 重量Weight | 0.60kg |
| 包装Package | 插卡blistercard |
| Model:HS-2.5B ForNon-lnsulatedTerminal | |
| 压接范围Crimpingrange | 0.5-2.5mm |
| 压接形式Crimping type | 点式Indent crimping |
| 长度Length | 230mm |
| 重量Weight | 0.60kg |
| 包装Package | 插卡blistercard |
| Model:HS-06C ForNon-lnsulatedTerminal | |
| 压接范围Crimpingrange | 0.5-6mm² |
| 压接形式Crimpingtype | 点式Indentcrimping |
| 长度Length | 230mm |
| 重量Weight | 0.60kg |
| 包装Package | 插卡blistercard |
1
| Model:HS-101ForNon-lnsulatedTerminal | |
| 压接范围Crimpingrange | 0.5-6mm² |
| 压接形式Crimping type | 点式Indentcrimping |
| 长度Length | 230mm |
| 重量Weight | 0.60kg |
| 包装Package | 插卡blistercard |
| Model:HS-102 ForNon-InsulatedTerminal | |
| 压接范围Crimpingrange | 0.5-10mm² |
| 压接形式Crimping type | 点式Indent crimping |
| 长度Length | 230mm |
| 重量Weight | 0.6kg |
| 包装Package | 插卡blistercard |
| Model:HS-103 ForNon-InsulatedTerminal | |
| 压接范围Crimpingrange | 0.5-6mm² |
| 压接形式Crimping type | 点式Indentcrimping |
| 长度Length | 230mm |
| 重量Weight | 0.60kg |
| 包装Package | 插卡blistercard |
1二
| Model:SN-02C ForNon-Insulated Terminal | |
| 压接范围Crimpingrange | 0.25-2.5mm² |
| 压接形式Crimping type | 点式Indent crimping |
| 长度Length | 190mm |
| 重量Weight | 0.37kg |
| 包装Package | 插卡blistercard |
| Model:HS-2o2BForNon-lnsulatedTerminalandconnector | |
| 压接范围Crimpingrange | 0.1-4mm² |
| 压接形式Crimpingtype | 旗型Flagcrimping |
| 长度Length | 180mm |
| 重量Weight | 0.17kg |
| 包装Package | 插卡blistercard |
| Model:Q-175,Q-200 For lead sealing | |
| 压接范围Crimpingrange | Φ10mm/Φ11mm |
| 长度Length | 160mm/185mm |
| 重量Weight | 0.32kg |
| 包装Package | 白纸盒whitepaperbox |
換向閥門 Reversing Valve 液壓工具專用液壓油(15#,32#) Special hydraulicoil for hydraulic tools(15#,32#)
C-18M 免鎖牙尖頭超高壓快速接頭 Lock free tip head ultra high pressure quick coupler
H形夾模
液壓泵浦檢壓表
常用壓力：700kgf/cm
螺紋：3/8"PT
Hydraulic pump pressure tester
Common pressure:7ookgf/cm2
Thread:3/8"PT
O
超高壓鋼絲強化油管
常用壓力：700kgf/cm
螺紋：3/8"PT
Ultra high pressure steel reinforced
oilpipe
Common pressure:7ookgf/cm2
Thread:3/8"PT
C-19M
鎖牙鋼珠頭超高壓快速接頭
Locksteelball headultra high
pressure quick coupler
Thread:3/8"PT
12ton壓力機檢壓表
12 Ton pressure tester
C-18
快速接頭
quickcoupler
鎖牙鋼珠頭超高壓快速接頭
Lock steel ball head ultra high
pressure quick coupler
Thread:3/8"PT
ISO9001 CE
RJIMU吉牧工具奇之力
玉環吉牧機械工具有限公司YUHUAN JIMUMACHINERYTOOLSCO.,LTD.（玉環縣臺震電力工具廠）
地址：浙江省玉環縣楚門鎮筠崗工業區Add: Jungang Industrial Zone, Chumen Town,Yuhuan,Taizhou City， ZhejiangProvince, China電話（Tel） :+86-576-87443633 87443636 87426768傳真（Fax）:+86-576-8742336687421616E-mail: qzl@qzltools.c0m E-mail:13967686718@139.comQQ：1159329118 Http://www.qzltools.com
