該頁無縮略圖
CCTV solutions for
hazardous & industrial
environments
CROUSE-HINDS
CCTV Systems and Solutions SERIES
CROUSE-HINDS
SERIES
Eaton’s Yuhua, Oxalis and HERNIS product lines deliver
a comprehensive portfolio of CCTV products and
turnkey systems. With specialist, reliable and highquality equipment and expertise, you can optimise
your operations whilst protecting your people, assets
and processes.
Eaton offers a specialised team of highly qualified
staff to ensure all aspects of engineering, design and
configuration within your project are fulfilled - from
initial stages of concept through to commissioning.
The Yuhua product line has been relied upon
by many industries to deliver high quality,
innovative products to meet customer and project
specifications.
Decades of experience in the fields of hazardous
and harsh industrial area CCTV solutions,
together with our specialist expertise, ensure that
customers are provided with the most reliable and
up-to-date technology available.
Proven solutions for hazardous and harsh industrial environments
This overview contains concise information on
Yuhua CCTV cameras and accessories for use in
hazardous and harsh industrial environments.
To use this guide, refer to the product group of
interest, read through the brief information and
select the specific product for your application.
For more detailed information and ordering codes visit
our website: www.eaton.com/cctv where a detailed
datasheet can be downloaded.
How to use this overview
Contents
Contents
Section Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–9
Hazardous areas guidance . . . . . . . . . . . . . . . . . . . 10–13
Cybersecurity . . . . . . . . . . . . . . . . . . . . . . . . . . . 14–15
Fixed camera stations . . . . . . . . . . . . . . . . . . . . . . . . . 18
PTZ camera stations . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Dome camera stations . . . . . . . . . . . . . . . . . . . . . . . . 20
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Camera ordering requirements . . . . . . . . . . . . . . . . . . 22
Industrial safe area cameras and accessories . . . . . . . . 23–25
125+ years of expertise and
innovation in the world’s most
harsh and hazardous areas
Rely on us as your CCTV system partner
By meeting extreme conditions with
customised solutions we can help you
achieve consistent operations, lower
costs, and most importantly, maintain
the highest level of safety possible.
Eaton’s reputation as a centre
of engineering excellence is
demonstrated by field-proven
products in the world’s most
demanding conditions.
With decades of experience in project
supervision and development, system
architecture and full turnkey solutions,
you can be sure you’re in safe and
reliable hands.
We provide end-to-end surveillance
solutions designed to meet the
challenges in the oil & gas, marine, and
mining industries.
Eaton provides integrated CCTV
system solutions covering all core
business processes generating
superior value for our customers. We
supply one stop offer for CCTV system
packages addressing the customer’s
every need including:
? project management
? needs-based design
? engineering
? testing/FAT
? commissioning/SAT
? training
? detailed documentation
? fast and competent systems
lifetime support
Eaton CCTV Systems and Solutions 5
Engineering
Engineering Services
Services
Engineering
services
Our specialised team is highly
qualified to ensure all aspects
of engineering, design and
configuration from its initial
stage of concept through to its
lifetime maintenance.
Engineering
Fully trained engineers construct all
of your solution’s system design and
engineering drawings, guaranteeing
all applications comply to the
relevant standards before during and
after installation.
Commissioning
As part of our standard
commissioning services we
not only arrange factory site
acceptance tests but once
our solutions are installed, we
ensure they are once again
subjected to engineering tests
to guarantee full, immediate
functionality.
Training
In order to ensure the benefits
of our solutions are fully utilised
we can provide your team
the necessary training for any
application. We want your staff
to feel competent and confident
that our solutions conform to your
requirements.
Technical support
In the case that additional
support is required after
installation, our Customer
Service team is available 24
hours a day for service and
onsite technical support to
make certain that any issue
is resolved effectively and
efficiently.
Project management
Each project is uniquely managed
throughout each stage of its lifecycle
from engineering, documentation,
factory acceptance test and
commissioning. We have the ability to
provide you with the necessary support
you need worldwide.
Marine & offshore applications
Our range of advanced CCTV solutions increase
safety and enhance efficiency on most types of
marine vessels. Typical surveillance areas include
engine rooms, cargo handling & mooring, pump &
compressor rooms and sub-sea mating on shuttle
tankers. The Yuhua safety focused solutions are
designed and approved to perform in the most
demanding of marine environments and operations.
Onshore and industrial applications
The Yuhua safety focused solutions are designed
& certified to perform in the most demanding of
environments and allow the end user to maximise
operational and lifecycle costs. All enclosures and
ancillary equipment are designed to exceed global
industry standards and allow quick replacement of
modules where required. Our cameras, excellent
support and backup service makes the CCTV
solutions from Eaton offer the reliable choice for
onshore and industrial projects.
Mining applications
The Yuhua safety & security focused solution utilises
the extended range of Yuhua camera stations.
Coupled with our advanced security features,
global certification, flexible control system including
system support & commissioning, it makes the
CCTV solutions from Eaton a reliable choice for multi
scalable mining projects.
Meet the demands of extreme conditions with customised solutions...
8 Eaton CCTV Systems and Solutions
China Merchants Shipping
Supply of CCTV systems to 110+ of VLCCs and BCs.
Products featured: Full IP CCTV system including harsh area PTZ
cameras, indoor safe-area cameras, NVR and control stations on
each vessel
Date of completion: 2022
Project highlights
Eaton CCTV Systems and Solutions 9
Bahrain Petroleum Company
BAPCO modernisation programme project
Products featured: Hazardous area PTZ and fixed camera stations
for BAPCO refinery CCTV system upgrade
Location: Bahrain
Date of completion: 2020
China Railway Construction Heavy Industry Corporation Limited
CRCHI Naples/Sicily Italy tunnel boring machine project
Products featured: CCTV and telephone system, including mining
Ex fixed cameras, telephones, and interface system
Location: Naples/Sicily Italy
Date of completion: 2023
Hazardous areas technical guidelines
Electrical equipment in potentially explosive atmospheres
Area classification
Introduction
Potentially Explosive Atmospheres exist where there is a risk of
explosion due to mixtures of gas/air, vapour/air, dust/air or other
flammable combinations.
In such areas there is a necessity to eliminate sources of
ignition such as sparks, hot surfaces or static electricity which
may ignite these mixtures.
Where electrical equipment has to be used in these areas it
must be so designed and constructed as to not create sources
of ignition capable of igniting these mixtures.
Before electrical equipment can be used in a potentially explosive
atmosphere a representative sample has to be fully tested and
certified by an independent authority such as Baseefa in Europe or
UL in the U.S.A.
Process plants are divided into Zones (European and IEC method) or Divisions (North American method) according to the likelihood of
a potentially explosive atmosphere being present.
Note : North American legislation now allows Zones to be used to classify areas, where this practice is used it follows the IEC Zone
method.
This information is intended as a guide only and further expert
guidance should be sought before placing into service, maintaining
or repairing any item of equipment in a Potentially Explosive
Atmosphere.
Where comparisons are shown between, for example, European
and North American practice this may be an approximation and
individual standards/codes of practice should be consulted for
precise details.
Eaton has been designing and manufacturing electrical equipment
suitable for use in potentially explosive atmospheres since one
century ago. We deal with all the major testing and certification
authorities throughout the world and have a diverse range of
internationally approved products.
European & IEC classification Definition of zone or division North American classification
Zone 0 (gases)
Zone 20 (dusts)
An area in which an explosive mixture is
continuously present or present for long periods
Class I Division 1 (gases)
Class II Division 1 (dusts)
Zone 1 (gases)
Zone 21 (dusts)
An area in which an explosive mixture is
likely to occur in normal operation
Class I Division 1 (gases)
Class II Division 1 (dusts)
Zone 2 (gases)
Zone 22 (dusts)
An area in which an explosive mixture is not
likely to occur in normal operation and if it
occurs it will exist only for a short time
Class I Division 2 (gases)
Class II Division 2 (dusts)
Class III Division 1 (fibres)
Class III Division 2 (fibres)
Gas & dust groups
There are two main gas groups, Group I - Mining only, Group II - Surface Industries and one combustible dust group - Group III.
These categories are used in European and I.E.C. groupings.
Group I is concerned only with underground mining where methane and coal dust are present.
Group II & Group III gases and dusts occurring in surface industries, are sub-grouped according to their volatility. This enables
electrical equipment to be designed to less onerous tolerances if it is to be used with the least volatile gases and dusts.
Typical gas/material European/I.E.C. gas & dust group North American gas & dust group
Methane I -
Acetylene IIC A
Hydrogen IIC B
Ethylene IIB C
Propane IIA D
Metal dust - E
Coal dust - F
Grain dust - G
Combustible flyings IIIA -
Non-conductive dust IIIB -
Combustible dust IIIC -
10 Eaton CCTV Systems and Solutions
Temperature
Types of electrical equipment suitable for use in potentially explosive atmospheres
Hot surfaces can ignite explosive atmospheres. To guard against
this all Electrical Equipment intended for use in a potentially
explosive atmosphere is classified according to the maximum
surface temperature it will reach in service. This temperature is
normally based on a surrounding ambient temperature of 40
degrees Centigrade (102 degrees Fahrenheit). This temperature
can then be compared to the ignition temperature of the gas(es)
which may come into contact with the equipment and a judgement
reached as to the suitability of the equipment to be used in that
area.
Many Eaton products are certified for use in ambient
temperatures up to 70 degrees Centigrade, see individual data
sheets for details.
Temperature classification Maximum surface temperature European/I.E.C. North American
T1 T1 450 o C
T2 T2
T2A
T2B
T2C
T2D
300 o C
280 o C
260 o C
230 o C
215 o C
T3 T3
T3A
T3B
T3C
200 o C
180 o C
165 o C
160 o C
T4 T4
T4A
135 o C
120o C
T5 T5 100 o C
T6 T6 85o C
e.g. Butane has an ignition temperature of 365 o Centigrade, equipment used in the vicinity of this gas would need a T rating of T2 or
higher
Different techniques are used to prevent electrical equipment from igniting
explosive atmospheres. There are restrictions on where these different types of
equipment can be used as follows:
European
Area of use
Designation
Standard
IEC
Area of use
Designation
Standard
USA
Area of use
Designation
Standard
Flameproof enclosure – an enclosure used to house electrical equipment, which
when subjected to an internal explosion will not ignite a surrounding explosive
atmosphere.
Zones 1 & 2
Exd
EN60079-1
Zones 1 & 2
Exd
IEC60079-1
Class I
Divisions 1 & 2
UL1203
Intrinsic safety – a technique whereby electrical energy is limited such that any
sparks or heat generated by electrical equipment is sufficiently low as to not ignite
an explosive atmosphere.
Zones 0,1 & 2
Exi
EN60079-11
Zones 1 & 2
Exi
IEC60079-11
Class I
Divisions 1 & 2
UL913
Increased safety – this equipment is so designed as to eliminate sparks and hot
surfaces capable of igniting an explosive atmosphere.
Zones 1 & 2
Exe
EN60079-7
Zones 1 & 2
Exe
IEC60079-7
-
Purged and pressurised – electrical equipment is housed in an enclosure which
is initially purged to remove any explosive mixture, then pressurised to prevent
ingress of the surrounding atmosphere prior to energisation.
Zones 1 & 2
Exp
EN60079-2
Zones 1 & 2
Exp
IEC60079-2
Class I
Divisions 1 & 2
NFPA496
Encapsulation – a method of exclusion of the explosive atmosphere by fully
encapsulating the electrical components in an approved material.
Zones 1 & 2
Exm
EN60079-18
Zones 1 & 2
Exm
IEC60079-18
-
Oil immersion – the electrical components are immersed in oil, thus excluding the
explosive atmosphere from any sparks or hot surfaces.
Zones 1 & 2
EExo
EN60079-6
Zones 1 & 2
Exo
IEC60079-6
Class I
Divisions 1 & 2
UL698
Powder filling – equipment is surrounded with a fine powder, such as quartz,
which does not allow the surrounding atmosphere to come into contact with any
sparks or hot surfaces.
Zones 1 & 2
EExq
EN60079-5
Zones 1 & 2
Exq
IEC60079-5
-
Non-sparking – sparking contacts are sealed against ingress of the surrounding
atmosphere, hot surfaces are eliminated.
Zones 1 & 2
Exn
EN60079-15
Zones 1 & 2
Exn
IEC60079-15
-
Eaton CCTV Systems and Solutions 11
Selection, installation and maintenance of electrical equipment intended for use in
potentially explosive atmospheres
The certification process
North American practice
European practice
All equipment, both electrical and mechanical, intended to be put into service within the EEC has to be certified in accordance with
the ATEX Directive.
International and national standards are published giving details of requirements for the safe use of electrical equipment in potentially
explosive atmospheres as follows:
Eaton recommends all explosion-proof electrical equipment is maintained, by suitably trained personnel, in accordance with the
manufacturers’ recommendations.
Any spare parts used should be purchased from the original manufacturer and repairs should be carried out by the manufacturer or under
his supervision, in order that the item remains in conformance with the certification documents.
All electrical equipment, intended for use in a potentially explosive atmosphere, should be certified as suitable for such use.
The methods of obtaining certification differ in detail, see below, between each certifying body or group of bodies (e.g. CENELEC). Basically
this process consists of supplying a representative sample of the equipment along with a set of drawings to a recognised test/certification
body e.g. Baseefa 2001 who in turn test the equipment against a recognised standard e.g. EN60079-14 and issue a certificate. The user of
the equipment can then refer to this certificate to enable him to safely put the item into service in a zone appropriate to the certification.
Sample equipment and supporting documentation are submitted to the appropriate authority e.g.U.L., F.M., C.S.A. The equipment is
tested in accordance with relevant standards for explosion protection and also for general electrical requirements e.g. light fittings.
After successful testing a listing is issued allowing the manufacturer to place the product on the market. The product is marked with the
certification details, such as gas groups A, B, C, and D, and area of use, e.g., Class 1 Division 1.
It should be noted also that mechanical equipment is covered by the ATEX Directive so items such as gearboxes must carry ATEX
certification.
The equipment coding signifying compliance with ATEX is as follows
International Europe U.S.A.
General recommendations IEC60079-14 EN60079-14 N.E.C. Chapter 5
Classification of hazardous areas IEC60079-10 EN60079-10 N.E.C. Chapter 5
Inspection and maintenance of electrical equipment IEC60079-17 EN60079-17 -
Requirements for flameproof enclosures IEC60079-14 EN60079-14 N.E.C. Chapter 5
Requirements for intrinsically safe equipment IEC60079-14 EN60079-14 N.E.C. Chapter 5
Requirements for increased safety equipment IEC60079-14 EN60079-14 N.E.C. Chapter 5
Requirements for purged and pressurised equipment IEC60079-14 EN60079-14 N.E.C. Chapter 5
Requirements for non-sparking equipment IEC60079-14 EN60079-14 -
II2GD i.e.
– Explosion proof in accordance with ATEX.
II – Group II surface industries.
2 – category 2 equipment (suitable for use in Zone 1) note: Category 1 is suitable for Zone 0.
Category 3 is suitable for Zone 2.
G – suitable for atmospheres containing gas.
D – suitable for atmospheres containing dusts.
Equipment will be CE marked when certified to ATEX.
12 Eaton CCTV Systems and Solutions
Worldwide approval
Ingress protection
The objective of the IECEx System is to facilitate international trade in equipment and services for use in explosive atmospheres, while
maintaining the required level of safety.
The IECEx and ATEX standards have been technically identical since 2006. IECEx is internationally recognised and accepted worldwide,
ATEX is recognised across Europe and is a mandatory requirement in the EEC.
Equipment certified under the IECEx system (and equivalent ATEX standards) carries the following coding:
Gb
Db
Where:
Two digits are used to represent the ingress protection level that applies to a given apparatus.
Most countries outside Europe or North America use IEC Standards as the basis for their own national standards.
In Brazil (Inmetro) and China, certification is typically based on compliance with IEC international standards.
The Russian Federation and Kazakhstan certify equipment according to CUTR standards, which closely follow IEC practice.*
In Russia, certain products used in fire alarm systems may require Russian Fire Approval.
Note that not all Eaton products certified to CUTR are also approved under Russian Fire Certification by fault. Please refer to the technical
data sheets for detailed specifications before placing an order.
*Note: There is an important change to the Ex certification system for Russia and Kazakhstan. The previous GOST R and GOST K certificates
are no longer being renewed and have been replaced by CUTR certification. The new certification applies to Russia, Kazakhstan and
Belarus, which have formed a customs union. All Eaton products previously certified under GOST R and GOST K standards are now certified
under CUTR.
Ga - Suitable for Zone 0
Gb - Suitable for use in a Zone 1 surface industries area in the
presence of gas
Gc - Suitable for Zone 2
Da - Suitable for Zone 20
Db - Suitable for use in a Zone 21 surface industries area in the
presence of dust
Dc - Suitable for Zone 22
In North America, ingress protection is typically described using NEMA standards, as follows:
? NEMA 3 is similar to IP55
? NEMA 4 is similar to IP66
? NEMA 4x is similar to IP66
? NEMA 6 is similar to IP67
All specifications, dimensions, weights, and tolerances listed above are nominal (typical). Eaton reserves the right to modify any data without prior notice. No liability is accepted for any consequences resulting from the use of this information.
6
I P
6 7 DUST
Non protected
0 Protected against a solid object
greater than 50mm, such as a
hand. 1 Protected against a solid object
greater than 12mm, such as a
finger. 2 Protected against a solid object
greater that 2.5mm, such as a
screwdriver. 3 Protected against a solid object
greater that 1mm, such as most
screws and wires. 4 Dust protyected. Prevents ingress
of dust sufficient to cause harm. 5 Dust tight. No ingress of dust.
SOLIDS
0 Non protected.
Protected against vertical
dripping water. Limited liquid
1 entry.
Protected against vertical
dripping water when tilted up
2 15?. Limited liquid entry.
Protected against vertical
spraying at an angle up to 60?.
3 Limited liquid entry.
Protected against vertical
spraying at an angle up to 60?.
4 Limited liquid entry.
Protected against jets of water
from all directions. Limited liquid
5 entry.
Protected against strong jets of
water from all directions. Limited
6 liquid entry.
Protected against the effects of
water immersion between 15cm
7 & 1m.
Protected against the effects of
water immersion (user specified
8 depth and duration test)
LIQUIDS
6
WATER
Eaton CCTV Systems and Solutions 13
Cybersecurity
Cybersecurity has never been more important
Certified labs dedicated to reducing cybersecurity risks
Our approach to managing cybersecurity risks
For years, Eaton has maintained strict procedures at every stage of the product development process. This discipline has paved the way for
collaboration with renowned standards leader, UL (Underwriters Laboratories), to establish measurable cybersecurity criteria for networkconnected power management products and systems.
Eaton introduced the first research and testing facility approved to participate in UL’s Cybersecurity Client Lab Validation programme in
Pittsburgh, Pennsylvania. And in 2018, UL approved a second Eaton lab to join the programme — another industry first — in Pune, India.
These accredited lab environments provide the global capability to test Eaton products with intelligence or embedded logic to key aspects
of the UL 2900-1 1 Standard.
In addition, the Eaton programme has most recently expanded to include cybersecurity certifications under the IEC (International
Electrotechnical Commission) 62443-4-2 standard as well as UL 2900-1 for Eaton’s Gigabit Network Card and Industrial Gateway Card. This
makes Eaton the first company in our industry to receive dual product certifications under IEC and UL standards.
Connected devices and the vast
amounts of data they generate create
opportunities and risks for organisations
— from manufacturing and testing to
installation and service.
As organisations expand their digital
footprint, it becomes imperative
to protect the availability, integrity
and confidentiality of their systems.
Cybersecurity threats must be taken
seriously and met proactively with a
system-wide defensive approach specific
to organisational needs.
We recognise that no protection method
is completely secure. A “defence in
depth” mechanism that is effective
today may not be effective tomorrow
because the ways and means of
cyberattacks constantly change. This is
why administrators of industrial control
system networks must be ever-alert to
changes in cybersecurity and work to
prevent any potential vulnerabilities.
14 Eaton CCTV Systems and Solutions
More security leads to less uncertainty
Security built into our
CCTV products from
the start
Safeguard CCTV
products and solutions
Ours is a secure-first methodology: our CCTV products meet rigorous cybersecurity and safety design
and testing standards before they’re made part of digital ecosystems.
Our Secure Development Lifecycle (SDL) spans the lives of our CCTV products. The framework
provides control and management throughout all phases of integration—from product design and
development through integration, installation, operation and support.
Define all processes
As product complexities, threat scenarios and technologies evolve,
procedures that identify and eliminate threats are a must.
Our camera products are developed with a cybersecurity-first mindset to ensure that past, current and
future vulnerabilities are accounted for. Our two-phased approach helps create a solid, secure CCTV
network foundation:
Secure products by design
In a world of ubiquitous connectivity, trusted equipment is the backbone
of safe environments.
1
2
How we help enable secure environments
In a hyper-connected world, trusted environments are a must. Eaton’s commitment to defending those environments comes to life at
our Product Cybersecurity Centre of Excellence, where our experts discover new ways to help protect products and systems against
cyberattack, provide internal training and help customers deploy and maintain secure solutions.
At Eaton, cybersecurity is part of our DNA and an integral consideration, with strict protocols placed on the people, processes and
technologies within our Secure Development LifeCycle process (SDLC), the programme that integrates security protocols at every phase of
product creation. SDLC spans from inception through to deployment and maintenance, enforcing cybersecurity best practices via training,
threat modelling, requirements analysis, implementation, verification and ongoing support.
Additionally, our cybersecurity best practices extend beyond our own labs to help keep our customers informed about potential
vulnerabilities and provide industry insights well as tools and other educational content.
A trusted cybersecurity CCTV
partner protects your digital assets
Our IP camera products enable customers to
remotely monitor their assets and process control
in a good and safe condition. Beyond physical
security, we provide trusted cybersecurity benefits
for digital assets.
Eaton CCTV Systems and Solutions 15
Protect your people,
assets and processes
CCTV
camera stations
Yuhua’s range of CCTV camera stations includes both explosion-proof and safe-area
monitoring equipment, designed for use in harsh and demanding environments. The
hazardous-area camera stations are certified to ATEX, IECEx, or CNEx standards and
have been tested for use in explosive and flammable atmospheres.
All of the pan-tilt-zoom (PTZ), dome and fixed camera stations are available in 316L
or 304 stainless steel, with a variety of camera options offering different zoom ranges.
Continuous 360° pan rotation provides an unrestricted view of the surrounding area
and is available on all PTZ models.
A complete list of available configurations can be found in the table on page 22.
For more information, please contact your local Eaton sales team. Contact details are
provided on the back cover of this brochure.
Constructed from 304 or 316L stainless steel and
specifically designed for use in hazardous areas
and harsh environmental conditions, Eaton’s hardwearing and corrosion-resistant camera stations
are suitable for a wide range of applications. They
are ideal for both onshore and offshore use in
industries such as oil & gas, marine, wind, chemical,
and many others where quality and durability are
essential.
Certified to ATEX, IECEx, or CNEx standards,
Eaton’s fixed camera stations come with standard
zoom capability and offer a variety of mounting
brackets, wiper/wash tank options, POE, EOC, and
fibre optic configurations. These features ensure
reliable performance in the most demanding CCTV
applications.
Fixed camera station range YHH30B
EACF-101B EATC-01
MineCAM
EACF-211
*See our datasheet for full technical specifications.
18 Eaton CCTV Systems and Solutions
Constructed from 304 or 316L stainless steel and
specifically designed for use in hazardous areas
and harsh environmental conditions, Eaton’s hardwearing and corrosion-resistant camera stations
are suitable for a wide range of applications. They
are ideal for both onshore and offshore use in
industries such as oil & gas, marine, wind, chemical,
and many others where quality and durability are
essential.
Continuous 360° pan rotation and tilt from
-90° to +90° provide an unrestricted view of
the surrounding area. The belt-driven gearbox
design ensures smooth movement and long-term
reliability, minimising mechanical friction and
preventing internal damage.
Certified to ATEX, IECEx, or CNEx standards and
equipped with ONVIF protocol as standard, Eaton’s
PTZ camera stations offer multiple optical and
thermal camera block options, delivering robust
performance for the most demanding CCTV
applications.
PTZ camera station range
YHW-HD-031 YHPTZ41B-1
YHPTZ41B
YHW750
YHW-HD-032
*See our datasheet for full technical specifications.
Eaton CCTV Systems and Solutions 19
Dome camera station range
Constructed from 304 or 316L stainless steel and
specifically designed for use in hazardous areas
and harsh environmental conditions, Eaton’s
hard-wearing and corrosion-resistant dome
camera stations are suitable for a wide range of
applications. They are ideal for both onshore and
offshore use in industries such as oil & gas, marine,
wind, chemical, and many others where quality
and durability are essential.
Continuous 360° pan rotation and tilt from -90°
to +90° provide an unrestricted view of the
surrounding area.
Certified to ATEX, IECEx, or CNEx standards and
equipped with ONVIF protocol as standard, Eaton’s
dome camera stations offer a variety of mounting
bracket options and deliver reliable performance
for the most demanding CCTV applications.
YHQ60 YHQ80 YHQ70 EACD-3021
*See our datasheet for full technical specifications.
Wash spray system
This YHWS wash spray system has been designed
as peripheral of Yuhua fixed and PTZ camera
stations with CNEx approved solenoid valve
specifically for use within hazardous, harsh and
demanding environmental conditions.
With the pressured water tank, the water can be sent
up to 30 metres high to clean the window glass of
camera station.
The system is suitable for use across a wide range
of applications with the option of 304 stainless steel
(polished or painted) or 316L stainless steel.
Mounting bracket
All mounting brackets are made from high-quality 304
or 316L stainless steel. They are available in a variety of
configurations to suit different applications, including
fixed, wall, pole, and swivel mounts, and also offer
engineering flexibility for customised solutions.
Each bracket is designed in accordance with the
camera station’s safe working load and vibration
handling specifications.
Junction box
Made from 304 or 316L stainless steel and specifically
designed for use in hazardous areas and harsh
environmental conditions, these hard-wearing,
corrosion-resistant junction boxes are ideal as CCTV
auxiliary equipment. They are suitable for both
onshore and offshore applications in the oil & gas,
marine, wind, chemical, and other industries where
quality and durability are essential.
With built-in power modules, media converters,
and engineering flexibility, the junction boxes meet
even the most demanding power and transmission
requirements.
Accessories
YHWS
YHZ-B6
YHZ-B5
YHZ-B20
YHZ-B18
YHZ-F1
KJ2028E-III
EABU-104
*See our datasheet for full technical specifications.
*See our datasheet for full technical specifications.
*See our datasheet for full technical specifications.
Eaton CCTV Systems and Solutions 21
Camera station ordering requirements
The following code is designed to help in selection of the wanted features with camera products. In terms of the availability of those
features please consult Eaton technical sales department who will support you to find the exact range meeting the application needs.
Supply voltage
24 VAC ±10% 50/60 Hz
110-240 VAC ±10%
127 AC ±10%
24 VDC
POE
12 VDC
Intrinsic safe 12 VDC
Special
Code
1
2
3
4
5
6
7
S
Video type
HP IP system
Code
I
Thermal core module
Resolution 640 x 512, supports
temperature measurement
No thermal core module
Special, needs engineering validation
Code
6
N
C
Housing type
Visual camera
Thermal camera
Dual optical and thermal camera
Code
V
T
D
Thermal core lens
25 mm focal length
No thermal core lens
Special, needs engineering validation
Code
6
N
C
Wiper options
Integral wiper
No wiper
Code
E
N
Camera rotation
Continuous rotation
Not applicable
Code
1
N
Video system
HD IP
Code
I
Temperature type
T6, 0 ?C to +40 ?C
T6, -20 ?C to +60 ?C
T6, -40 ?C to +60 ?C
T5, -40 ?C to +65 ?C
T6, -40 ?C to +65 ?C
T5, -40 ?C to +70 ?C
Not applicable
Code
0
1
2
D
E
F
N
Protocol requirements
Pelco D/P protocol
Not applicable
Code
D
N
Cable tail length
0
3M
5~7M
10M
3M armored
5~7M armored
10M armored
Special, needs
engineering
validation
Code
0
1
2
3
1A
2A
3A
S
Certification
ATEX
IECEx
MA
ATEX & IECEx
ATEX & IECEx & CCC
CNEx
No EX certification required
Code
A
I
M
Q
3
X
N
Material
304 stainless steel
316L stainless steel
Code
A
B
Surface finish
Natural
Powder coated
Polished
Code
A
B
C
Visual camera
22x zoom 3 MP HD IP camera
33x zoom 3 MP HD IP camera
22x zoom 5 MP HD IP camera
Special, needs engineering validation
Code
U
V
W
C
Transmission type
Standard
Ultra Ethernet
Ultra Ethernet with surge
protection
Simplex singlemode 9/125 μm
ethernet
Simplex multimode 50/125 μm
ethernet
IP over Coax
Duplex Singlemode 9/125 μm
Duplex Multimode 50/125 μm
Power network lightning
protection
Special
Code
0
1
2
3
4
5
6
7
8
S
22 Eaton CCTV Systems and Solutions
From extreme to everyday, from
hazardous areas to industrial floors –
a new chapter in industrial vision.
For decades, we’ve been trusted in the world’s most hazardous environments – oil & gas, marine, and
mining sites, with explosive gas and dust.
Our explosion proof type camera stations have been proven in countless projects where failure is not
an option.
Now, we’re bringing that same engineering excellence to regular industrial applications.
Introducing our new camera series: a range expansion designed for everyday industrial use. Built
with the same commitment to quality but optimised with lighter materials and cost-effective design -
perfect for factories, warehouses, and utility sites.
This new line is not just a product - it’s a promise. A promise that even in less extreme conditions,
you can rely on the legacy of a manufacturer who knows what it takes to protect people, assets, and
operations.
Eaton’s industrial safe area camera range is
engineered for reliability and clarity across
demanding environments. The portfolio includes
indoor and outdoor models - fixed, and PTZ (pantilt-zoom), offering a variety of resolutions and lens
configurations to suit diverse surveillance needs.
These ONVIF-conformant, full HD IP cameras
feature integrated illuminators and advanced
imaging technologies such as True Wide
Dynamic Range (WDR), Digital Defog, and Day/
Night functionality. Intelligent features ensure
exceptional image quality in all lighting conditions,
making them an ideal solution for industrial
and commercial applications where durability,
performance, and visual precision are paramount.
Industrial safe area camera range
IDF01A-402FF1
IDF01A-404FF1
IBF01A-402FF1
IBF01A-404FF1
ITF01A-405XF1
IBF02A-405XF1 1
ITP01A-244X06
IDP01A-225XT1 IDP02A-233XU4
*See our datasheet for full technical specifications.
24 Eaton CCTV Systems and Solutions
PB01
CPB01-22
Pole mount
Ceiling mount
Inclined ceiling mount
Corner mount
Wall mount
CB01 ICM01
WB01-JB
WB03
WB01
WBG01
WB04
WJB03 CJB02
Accessories
Mounting bracket
Eaton’s industrial mounting brackets are constructed
from robust aluminium alloy or stainless steel,
ensuring durability and corrosion resistance in
industrial environments. Available in a wide range of
configurations - including fixed, wall, pole, and ceiling
mounts - they offer versatile installation options to suit
virtually any application.
Engineered with flexibility in mind, these brackets also
support customised solutions to meet specific project
requirements. Each bracket is designed in accordance
with the camera station’s safe working load and
vibration handling specifications, ensuring secure and
stable performance in demanding conditions.
Junction box
Eaton’s industrial junction boxes are designed for
secure and streamlined camera installation. Engineered
for durability and ease of use, they support rear cable
routing to maintain a clean and protected setup in
both indoor and outdoor environments.
With a compact footprint and a lightweight design,
the junction boxes offer reliable mounting while
minimising structural load. Its corrosion-resistant
construction ensures long-term performance in
industrial and commercial applications, making it an
ideal accessory for enhancing camera deployment
flexibility and protection.
*See our datasheet for full technical specifications.
*See our datasheet for full technical specifications.
Eaton CCTV Systems and Solutions 25
Notes
Notes
Follow us on social media to get the
Eaton is a registered trademark. latest product and support information.
All other trademarks are property
of their respective owners.
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
? 2025 Eaton
All Rights Reserved
Printed in China
Ref: Yuhua CCTV Overview/B
September 2025
For more information:
If further assistance is required, please contact an authorized Eaton Distributor, Sales Office, or Customer Service
Department.
Europe (U.K.)
Unit B, Sutton Parkway
Oddicroft Lane
Sutton in Ashfield
United Kingdom
NG17 5FB
TEL: 44 0 1623 444 400
MEDCsales@eaton.com
China
No.189 Liuyanghe Road
Xinbei District
Changzhou
China
Yuhuasales@eaton.com
UAE
National Industries Park –
Jebel Ali (South)
P.O. Box 261768
Dubai
United Arab Emirates
TEL: 971 4 8066100
Singapore
100G Pasir Panjang Road
#07-08 Interlocal Centre
Singapore 118523
TEL: 65 6825 1668
HACAsia@eaton.com
Eaton's Crouse-Hinds business
1201 Wolf Street
Syracuse
New York 13208
United States
TEL: 877 932 9322
crousecustomerctr@eaton.com
Australia
10 Kent Rd
Mascot NSW 2260
TEL: 61 1300 332 866
FAX: 61 2 9693 5127
crousehindsanz@eaton.com
Malaysia
B-29-3A, Block B, Jaya One
No. 72A, Jalan University
46200 Petaling Jaya
Malaysia
TEL: 60 3 7955 3399
FAX: 60 3 7955 1399
South Korea
7th Fl, Parkland Building
601, Eonju-ro, Gangnam-gu
Seoul 100-744
Korea
TEL: 82 2 6380 4833
